Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

What's the preferred glue

Posts

What's the preferred glue

#1

What's the preferred glue

Carole Valentine

>for bonding PVC to MDF for a shop made drum chuck? I hate Gorilla glue. Epoxy? 5 min kind? Something else? I used the 5 min epoxy on the first one and it seemed to work well, but I wondered what others use.

Re: What's the preferred glue

#2

Re: What's the preferred glue

john lucas

>Carole 5 minute epoxy worked for me although I made my last one out of a PVC end cap so I was able to mount the pvc directly to my faceplate. I did have to use silicone caulk at the screw holes to keep them from leaking the vacuum.

Re: What's the preferred glue

#3

Re: What's the preferred glue

Jorge Castaneda~Downeast Maine

>Carole,

I think they are two incompatible materials for bonding, PVC needs a solvent and is non porous, so unless you abrade or partially drill holes in the PVC for the epoxy to get in, it is not going to work.

John's solution is a better way. I have bonded those two in construction using 3M's 5200 rubber, an industrial adhesive, takes about a week to set, and then is there for good, using this you could make a grove in the MD to fit the PVC and then bed it with the 5200.

Jorge

Re: What's the preferred glue

#4

Re: What's the preferred glue

Bill Howatt

>I've made mine from MDF and ABS which is the black plastic drain pipe. I cut a groove about 1/8" or so deep the right diameter for the ABS and glue it in the groove with epoxy. I probably used 5 min but I'm not certain now. Before assembling I rough the part of ABS that will be in contact with the epoxy with some sandpaper. My theory is that this will clean the surface and put some fine scratches in the plastic to give the epoxy some "tooth"; don't know if it is necessary but it sure is a nice theory :).

Bill

Re: What's the preferred glue

#5

Re: What's the preferred glue

Carole Valentine

>Well, I used an epoxy on the 6" one that is suppose to bond wood, PVC and a host of other materials. Stinks like all get out, but I couldn't budge it once it set. I did put about a 1/4" grove in the MDF and then filled it with epoxy and bedded the PVC in it. I won't put it to use until after 24 hrs. I also scuffed the PVC with 80 grit before gluing.

Thanks for the input, everyone.

Re: What's the preferred glue

#6

Try silicone caulk

David Walser

>Carole,

Epoxy works and you should use that if you have it on hand. Silicone caulk also works and is easier and quicker -- assuming you have it on hand -- since it requires no mixing. As you did with the epoxy, just cut a groove in the MDF, fill the groove with silicone caulk, jam the PVC pipe home and allow the caulk to cure. I set the faceplate/MDF face up on my workbench and place a weight on the top of the PVC to act as a clamp overnight. (The weight is part of a barbell set I bought in a rash moment when I thought I should be exercising. This way, I get some use from it.) The excess caulk will form an air seal on both sides of the pipe.

Just another alternative.

Re: What's the preferred glue

#7

Re: What's the preferred glue

Bill Clark

>Carole, that's the process I used. I also shellaced the MDF to prevent it from leaking air. Been using three of these of various sizes for some time without any problems.

Re: What's the preferred glue

#8

Re: Try silicone caulk

arkie

>And always scuff up the part of the PVC you're going to glue, with a little 80 or even 60 grit. Regardless of which glue you're using, it increases surface are for the glue to grip.

Re: What's the preferred glue

#9

Re: Try silicone caulk

Carole Valentine

>I use my bar weights more in the shop than I EVER did for exercise! LOL

Re: What's the preferred glue

#10

Re: I use Hot Melt glue

Russ Fairfield

>Carole,

I use hot melt glue to hold the PVC pipe to MDF. I cut a recess in the MDF with a parting tool, and rough up the PVC for a good grip.

If you think about it, the glue doesn't have to be very strong.. You don't need the glue for anything other than a good seal once the vacuum is ON. Hot Melt works very well for that, and it is fast.

Re: What's the preferred glue

#11

My method

Dave Peebles Lyons, Ohio!

>Hi Carole,

Looks like you got it figured out. But I used thick CA glue on mine. It has been about ten years now, and they are still holding up just fine. Also, I never sealed the mdf. I didn't have any problems with leakage on them.

Dave


img

Re: What's the preferred glue

#12

Re: My method

Carole Valentine

>Dave, what do you use on the drum face? Looks like a huge O-ring! I have been using Foamies and they work just fine.

Re: What's the preferred glue

#13

Re: My method

Don Tewell in Central Illinois

>How come your shop is so CLEAN? I don't think I even have a horizontal surface in my entire shop that clean.

Re: What's the preferred glue

#14

Re: What's the preferred glue

Don Orr

>I have made 6 vac chamber chucks in the last few months-4" & 2" out of PVC and MDF. I direct threaded the MDF for my spindle threads (1"x8tpi & 1.25"x8tpi) and turned a groove in the MDF to fit the PVC as others have said. The first few I used an automotive RTV silicone sealer because I had it. The last few I used epoxy. Didn't rough up the pvc on either-both seem to be holding OK so far. I also coated the MDF with poly just because I had some extra. I also put a self adhesive rubber-like gasket on the spindle side of the MDF where it seats on the spindle. They seem to work pretty good. My pump is only a 1.5 cfm Gast but I can pull over 20" on solid wood. Not so much on porous wood though. ;-(

My lathe sucks really good now. :-))

Re: What's the preferred glue

#15

Good Point

Bill Howatt

>I hadn't thought about the external air pressure actually holding the chuck together. My usual thought is that things I mount on a vacuum chuck are relatively light weight, almost finished bowls.

Bill

Re: What's the preferred glue

#16

Re: What's the preferred glue

Carole Valentine

>Don, did you laminate the MDF so you had a thickness >= the spindle protrusion from the headstock or did you just use 3/4" MDF and let the spindle stick out through it? I have some 3/4" Azec (sp?) boards and am wondering if I could use them for that.

Re: What's the preferred glue

#17

Dick Hines

Re: What's the preferred glue

Dick Hines

>I have a piece of ultra-high molecular ployethylene left over from something else I was doing. I am going to get a Beall tap and tap threads to fit my lathe. Then turn the cup and drill the hole in the bottom. I got it form McMaster-Carr. This will do away with MDF and face plates. Will post the results when I get my chuck up and pumping.

Re: What's the preferred glue

#18

O-ring

Dave Peebles Lyons, Ohio!

>Hi Carole,

That is an O-ring. I found them at a local place. But they were soon changed out to the foamies. They got brittle over time and would tend to leave black marks on the wood.

These days I have a couple of the Oneway aluminum chucks, but these still get some use on certain things. I also switched over to the white foamies on the Oneway vacuum chucks. I think they are just about the best material I have found... plus the are dirt cheap.

Dave

Re: What's the preferred glue

#19

Clean shop

Dave Peebles Lyons, Ohio!

>Hi Don,

I am a bit of a neat freak, but you can believe me that it has never looked that clean since. :) The shop photos on the website were taken just after a major clean up. It will probably never look that good again... Unless I built a new shop. Then it will look real good for a couple of weeks.

Dave

Re: What's the preferred glue

#20

What's your spindle size?

Carole Valentine

>If it's 1 1/4 x 8 you can use my tap next time you are over this way instead of buying one. You probably have someone closer who has one.

Re: What's the preferred glue

#21

Laminated

Don Orr

>I glued 2 thicknesses of 3/4" MDF together with yellow glue. Not sure about the other stuff you mention.