Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Adding thickness to a bowl

Posts

Adding thickness to a bowl

#1

Adding thickness to a bowl

Steven Kubien

>Hey there,

I mis-measured the thickness on a bowl and now I have about 1/16"...possibly a little less on what was supposed to be a salad or fruit bowl. Certainly too thin to sell as it may crack/break if an apple gets dropped in it. Otherwise I really like the piece and I would like to salvage it.

So, I am thinking I would add a small (in height) foot. The bowl has a slightly concave bottom. I am planning on using epoxy to glue and provide a solid base under the concavity (got a better term?) because there is no way I will exactly match the foot against the bowl.

Does this sound at all reasonable to you? I know about life being short and turning crappy/screwed up wood but I think this will be a decent exercise to run through in case it ever happens with REALLY nice wood.

Your thoughts and suggestions are welcome and appreciated.

Steve Kubien

Ajax, Ontario

Re: Adding thickness to a bowl

#2

Re: Adding thickness to a bowl

John Veerkamp,Western Mo

>Steve, that would work.

Another solution is to turn out the bottom entirely and turn a base/plug foot of a contrasting wood. This is a design opportunity. I've intentionally made such bowls. They can be very striking. I use medium CA glue on the joint. I usually make the hole in the bottom tapered towards the inside. The plug foot is turned to match. Err on the side of making it too long. it will protrude into the bowl. reverse mount the bowl and carefully turn the new bottom . Try it .

Goog luck.

John

Re: Adding thickness to a bowl

#3

Re: Adding thickness to a bowl

john lucas

>steve I've made about every mistake there is including that one. Here is how I match the wood to the bottom of the bowl. I turned the bottom of the bowl round to match the curve as best I could. Then I mounted a blank on a glue block and turn the outside diameter of the foot I want. Then I started turning what I thought was the shape of the bottom of the bowl. If you happen to have one of those gadgets that will copy a curve it helps a lot. Then rub chalk on the bottom of the bowl and touch it to the new foot and rub it. The chalk will tell you where to cut. Do this until the chalk covers the whole thing or at least what will be the rim of the foot. If you get really close you can use wood glue. If in doubt use epoxy to fill any voids.

Re: Adding thickness to a bowl

#4

Re: Adding thickness to a bowl

Steven Kubien

>Thanks guys. I knew there were ways to do this.

Cheers,

Steve

Re: Adding thickness to a bowl

#5

Re: Adding thickness to a bowl

Don Evans

>Maybe I'm missing something here and if I am I'm sure someone will quickly point it out!

Trying to match the whole area on the bowl with an added base is the wrong way to go. By whole area, in this case, is defined as the area of the base that would come into contact with the bowl.

Instead I use this method on a lot of turning, spindle especially. I just hope I can put it into words clear enough.

For this project as I understand it, I would ONLY try to make the outside edge of the base closes to the bowl touch the bowl. Do this by cutting the hidden part of the base that goes towards the bowl at a back angle so it does NOT touch the bowl. I would then use a tendon in the middle of the base which goes into a hole in bottom of the bowl hold the thing together by epoxy.

By back cutting all of the base enough that it will not touch the bowl except on the edge (which I would make a knife edge) it will fit perfectly. The tendon and base should be dry fitted before gluing to make sure it will all go together without any gaps.

Back cutting hidden area's is an important skill for woodturning or metal turning (not to be confused with metal spinning) for that matter. One that I think is greatly overlooked.

Don

Re: Adding thickness to a bowl

#6

Re: Adding thickness to a bowl

john lucas

>Don I assumed that maybe he made the bowl too thin already at the bottom and there isn't room for a tenon. You only choices then are to add extra wood to the bottom or to go ahead and make a funnel and put a bottom in with wood coming through the bottom of the bowl. The second one always looks like a repair to me.

Re: Adding thickness to a bowl

#7

Have I got this right....

Steven Kubien

>Don, are you suggesting making (essentially) and shallow plate, with raised area in the middle where only the edge of the "plate" and the top of the raised area meet the bowl? That would be easier to execute than trying to match the entire bottom surface.

I am going to experiment with this and other methods. The good news is that I can take my time and do not have to rush anything.

Thanks!

Steve

Re: Adding thickness to a bowl

#8

Re: Have I got this right....

Don Evans

>That is the basic concept. I would make the middle piece like a dowel shape or use a dowel. If using a dowel, I would drill hole for it in the middle of the plate but not all the way thru then glue it after is tested for fit. The other end of the dowel I would also drill the bottom of the bowl for the dowel to mate into.

As John points out your bowl may be too thin to do that....

Its important to understand you cannot make the lip of the plate wide. What part of the lip that touches the bowl should be very narrow, maybe 1/16th inch wide.

You will also have to weight the bowl down carefully to the plate when you glue it as the expansion of the glue MAY move and cause a gap between the plate and bowl.

Don

Re: Adding thickness to a bowl

#9

Re: Have I got this right....

Steven Kubien

>Thanks Don. I think my bowl is too thin to go this route. You point about making the edge thin/sharp makes perfect sense and will still apply no matter how I do this.

Cheers,

Steve