Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Shopmade Chatter Tool

Posts

Shopmade Chatter Tool

#1

Shopmade Chatter Tool

Gil Jones

>One of the members of my turning club wanted to see a demo of a chatter tool that one could make from bits found around the shop. Since I did not have a chatter tool to do the demo with, I made one from things I found in various bins in my shop.

It is 24.765cm [9.75"] long (w/o the blade), the ferrel is a brass compression fitting nut that is screwed on and turned smooth, the handle is turned from a scrap piece of Mulberry wood and decorated with a few friction burns from a wire, the shaft is a piece of steel rod from an ink-jet printer that the ink trolley rides on, the blade holder is a bushing (mated to the shaft with a roll-pin), and the chatter blades are just jigsaw blades, ground to shape and bent a little. It works best with the rear screw in place and the front one removed.

It seems to work quite well at around 1000 rpm, on end-grain hardwood.

The price was right in that all the pieces were already in the shop, and not being used for anything else.

Gil


img

Re: Shopmade Chatter Tool

#2

Re: Shopmade Chatter Tool

Gil Jones

>Here is the front view.

Gil


img

Re: Shopmade Chatter Tool

#3

Steven Antonucci

Where did the second hex bolt go?

steve antonucci

>There are two in the first picture, but I only see one in the second picture? I need to make one of these someday, and like you, have all of the stuff in the shop to do it...

Steve

Re: Shopmade Chatter Tool

#4

I removed it

Gil Jones

>'cause it works better with just the aft one in place.

They are just 10-32 screws.

Gil

Re: Shopmade Chatter Tool

#5

Brad Vietje

Nice Tool, Gil

Brad Vietje

>Great job on that, and I like to steel source, especially.

I sharpen one of mine to a point, and the other to a rounded tip. You might play with the profile a bit and see what you like the best.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Shopmade Chatter Tool

#6

Thanks, Brad....Good ideas.

Gil Jones

>

Re: Shopmade Chatter Tool

#7

Re: Shopmade Chatter Tool

robo hippy

>I recently did a workshop for a few friends on boxes, and was playing with my chatter tool, when one guy said look at mine. He took a 3/8 spindle gouge, laid it on its side and drew it across the top of some sugar maple. Left a beautiful chatter pattern. Guess I have done that by accident when making a finish cut many times, but never on purpose.

robo hippy

Re: Shopmade Chatter Tool

#8

Compression fitting

Tony - Memphis

>When you say you turned the compression fitting, how did you do that? I've done a couple, but never was happy with my procedure. Thanks for any tips.

Tony

Re: Shopmade Chatter Tool

#9

Steven Antonucci

I use a spindle gouge

steve antonucci

>Brass cuts easily and you just have to take it slow...

Steve

Re: Shopmade Chatter Tool

#10

Re: Compression fitting alternative

GalenV in Iowa

>Tony

I use a Zurn PEX fitting that is nice heavy smooth brass. The 3/4" x 3/4" female solder adapter, cost $1.63 at Lowes. The smooth end is 1" OD x 7/8" ID and when cut off is 3/4" long. There is a male solder adapter that is 7/8" OD x 3/4" ID for smaller handles.

It probably varies from place to place but the compression nuts cost more where I am at and no need to turn off the outer hex. No need anyway other than we always so them smooth on a handle.

Galen

Re: Shopmade Chatter Tool

#11

Used a 1/2" bowl gouge...carefully...

Gil Jones

>also, used a 3/4" square nose scraper (all are HSS). It was smooth enough to start with 240 grit and finish with crocus cloth. Very light cuts at 800 rpm. This is not a biggie...brass is soft.

Gil

Re: Shopmade Chatter Tool

#12

Thanks

Tony - Memphis

>I used a parting tool to sort of scrape I guess and it worked ok, but it wasn't pretty! I'll try the other methods mentioned. I've also just used a file. Thanks for the help.

Tony