Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Jamieson boring rig project - - update

Posts

Jamieson boring rig project - - update

#1

Jamieson boring rig project - - update

Pete in Holland, MI

>A few weeks ago, I asked for input & tips from you guys on construction of a Jamieson boring rig. The following threads contain photos of the completed unit, as of tonight. It is pretty much by the book, with a few alterations. I have access to a lot of small machine parts & pieces that allowed me to build it pretty cheaply. Other than the tool holder, I think my costs have crept up to about $25 now.

Several folks had said that the boring bar should be some pretty stiff stuff. I found a piece of Thompson shafting that is case hardened & ground on the outside, and pretty tough on the inside. I had to heat & draw the temper so the end could be drilled & tapped.

The orange/blue thing overhead is the 3 volt lasers I mentioned a few weeks back. I have 3-4 dozen of them and will be offering them on the classifieds column in the near future, so stay tuned.

I also took the advice of several of you and contacted Lyle Jamieson. It so happens that he will be coming near my home town next month, and has agreed to come to my house for a day of chip making and education. Should be a fun day.

Unfortunately, the next couple evenings are booked, and this weekend, we depart for the coasts of Louisiana & Alabama for vacation next week, so it'll have to sit dormant for a couple weeks.

Whatcha think? Any input as to where it needs help or tuning? Yup, I can see that the lathe needs to move from the wall soon. Small basements suck.

Thanks all, and I'll keep you posted on how it works out.

Pete

Re: Jamieson boring rig project - - update

#2

Photo #1 

Pete in Holland, MI

>


img

Re: Jamieson boring rig project - - update

#3

Re: Photo #2 

Pete in Holland, MI

>


img

Re: Jamieson boring rig project - - update

#4

Re: Photo #3 

Pete in Holland, MI

>


img

Re: Jamieson boring rig project - - update

#5

Re: Photo #4 

Pete in Holland, MI

>


img

Re: Jamieson boring rig project - - update

#6

Re: Jamieson boring rig project - - update

paul waddle

>Where's the photos? The problem with boring out vessels with small openings,one must use a smaller than desirable boring bar. I would think a square or hex bar would be stronger, or perhaps some Thompson tubing,if the other prove to be problematical by buggering up the opening ? There seems always a compromise. For the present,I'm going to make my hollow in two pcs. pw

Re: Jamieson boring rig project - - update

#7

Ain't it the truth...........

Richard Jones

>Small basements DO suck, especially when you have a large bench in the way of moving your lathe away from the wall!!! But I digress........

Great looking rig, I have copied your pics, hope to make something similar eventually.

Paul, can you share some details about your good looking dust collector hood?

Thanks.

Rich

Re: Jamieson boring rig project - - update

#8

Re: Ain't it the truth...........

Don wilcut

>Ditto on the hood, Great setup.

Re: Jamieson boring rig project - - update

#9

Re: Jamieson boring rig project - - update

Rick Allen

>Drill a small hole in the end of the "D" handle to put a nail through. That mail will prevent the "D" handle from coming out of the back rest when the boring bar is in use. Imagine not how the "D" handle can come out of the back rest but what would happen IF the "D" handle were to come out of the back rest while the tool was in use.

Re: Jamieson boring rig project - - update

#10

Re: Photo #1

john lucas

>pretty cool and good job on the lazar holder joints. Did you make those or are they store bought?

I would mount the captured tool rest so the overhang on the bed goes to the back. 180 degrees from how you have it mounted now. I often swing the captured tool rest about 45 degrees or looking from the top about 8 oclock. This lets me get into the upper corners of hollow vessels with using the curved bars. Also helps reach into the flying saucer shaped vessels.

Re: Jamieson boring rig project - - update

#11

Re: Ain't it the truth...........

Carol - now back in Dubuque, IA

>me too on the hood

Re: Jamieson boring rig project - - update

#12

Hood

Pete in Holland, MI

>The hood is framed with 3/4" plywood on both sides, tied together with a couple 1x2's on the top & bottom, and wrapped & nailed with some 1/16" polyethylene sheet that I had. Part of a PVC elbow out the side allows a 4" flexible duct connection (shared with my adjacent shaper for now). From the bottom, several pieces of wood are screwed together to give me an extension from the bed, and a pad to clamp to the side of the bed with a c-clamp from underneith. This pad will have to be taylored to match the profile of your lathe bed.

It won't suck chips, but does do well keeping my sanding dust under control during bowl turning.

I'll shoot a couple pictures tonight.

Re: Jamieson boring rig project - - update

#13

Brad Vietje

Re: Jamieson-STYLE Boring Bar

Brad Vietje

>Pete,

Looks like a great project, and you've done a good job of it, but since Lyle Jamieson often contributes his experience here -- and just to be fair -- it isn't really a Jamieson boring bar unless it came from Lyle Jamieson.

For those of us without the D-I-Y metal working skills and tools, I believe the original is still available from a number of outlets.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Jamieson boring rig project - - update

#14

What Rick said

Steven Kubien

>I can only imagine the chaos if the D handle came out of the support while the lathe was running. Definately a trip to the ER, plaastic surgeon and possibly orthopaedic surgeon as well.

Be safe,

Steve

Re: Jamieson boring rig project - - update

#15

Re: Jamieson-STYLE Boring Bar

Pete in Holland, MI

>Brad -

Good point. "Jamieson-style" should be the title.

Yes, Lyle does have these available from various outlets. I just decided to build my own. With 2 kids in college, disposable cash is tight. With Lyle having the general plans on his website, and having been in contact with him several times in the project, I don't feel like I am taking anything away from him. When asked, his reasoning to post the general plans is that not everybody has access/talents in metal working, thus the risk of loss of business is low. He just wants people to have fun.

Great guy over the phone. Looking forward to meeting him in the near future.

Pete