Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

diamond parting tool

Posts

diamond parting tool

#1

diamond parting tool

john lucas

>last year I purchased a Packard brand diamond parting tool. I've always been happy with the Packard house brand tools that I have bought in the past but this one just doesn't seem to hold an edge. Anyone have a diamond parting tool that they like. I'm looking for a new one. Wish Doug Thompson made one of these. :)

I have a flat parting tool that I bought at the flea mkt for $2.50 that I love but it's a little wide and kind of short. I also like my Craftsman carbon steel diamond parting tool but since I know it doesn't hold an edge long I save it for special cuts because it cuts so clean and it's also kind of narrow and doesn't work as well when I'm using calipers with it.

Re: diamond parting tool

#2

Re: diamond parting tool

John K Jordan

>My favorite is a Craftsman HSS diamond parting tool. I got it in an inexpensive set of HSS tools about 8 years ago but I don't know if they still sell it.

Hey, for the price of one of Thompson's scraper blanks, a grinding wheel, a homemade fixture, and a measure of patience you could own the very first Thompson Diamond Parting Tool!

JKJ

Re: diamond parting tool

#3

Re: diamond parting tool

DavidWalser

>John,

I have an M2 diamond parting tool from Hamlet that I like a lot. It holds its edge well and does not flex. It feels good in my hand and I can easily peel away the wood with the parting tool in one hand and my calipers in the other.

Having said that, I don't know that I'd prefer this parting tool over one made with a similar grade steel by Henry Taylor, Crown, or Sorby. I mean, how important is "feel" in a parting tool? I just checked CSUSA's site and found that the Hamlet M2 parting tool is less expensive than the other name brands and only a few dollars more than CSUSA's Artisan brand (made by Henry Taylor). I probably bought it because it was cheaper.

Re: diamond parting tool

#4

Mike Stafford

Re: diamond parting tool

Mike Stafford

>John, I also have a Packard 3/16" diamond parting tool. It seems to me that it does not hold its edge as well as the Crown 3/16" parting tool that is my favorite. I bought the Packard parting tool from someone here on WC who was selling some tools for for the widow of a turning friend. Try the Crown. I think it is a good tool for the money and is much less expensive than the Sorby 3/16" diamond.

As I said the Packard does not seem to hold its edge as long but it cuts fine while sharp.

My favorite parting tool is the Sears HSS 1/8" diamond. I have a few of them from when they were closed out a few years ago and I picked them up for $7 each. I am still working on the original one and I use it all the time.

I also have a Sorby 1/8" plain which is a fine tool but for some reason I always reach for the diamond tools first.

Re: diamond parting tool

#5

Re: diamond parting tool

john lucas

>So it seems like we all like the sears parting tool. My only problem with it is that I use dial calipers a lot when turning duplicate turnings and the narrow gap of the sears tool is just too close to the size of my caliper jaws making it tricky. I like a thicker gap for those cuts consequently I bought the Packard tool. I'll check out the Henry Taylor, I have 2 other HT tools and like them very much.

If you see the older brown handle sears parting tools at the flea mkts. pick them up. They are great tools. You can blue the tip in a heartbeat while sharpening so use a very light touch. I touch the heel of the tool and then lift the handle until I see sparks come over the tip and quickly remove it.

Re: diamond parting tool

#6

Ric Taylor

Re: diamond parting tool

Ric Taylor

>Can you grind down the jaws of your caliper to make them thinner?

Ric