Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Wolverine setup

Posts

Wolverine setup

#1

Wolverine setup

Don Orr

>I am finally getting ready to replace my old home made sliding rest for sharpening gouges. I have a Oneway Wolverine grinding jig that I want to set up on my Craftsman 8" grinder. The directions show that the platform on which this all sits should be 6 1/4" below the center of the wheel. The center of my wheel is 7" above the platform now. As it is I will have to cut off part of the chute in the back of the grinder to get the jig base under the grinder. I don't see how I can obtain the 6 1/4" height described in the directions. (Yes I read directions). If I put a riser block under the jig base it will be very close to the wheel and the shroud will probably be in the way. Does any of this really matter or can I just mount the jig base under the wheel at whatever height I already have and call it good. What have you all done ?

Re: Wolverine setup

#2

Re: Wolverine setup

Gordon Seto

>The wheel is round; you are always grinding at the tangent of the wheel. As long as your guard doesn't interfere with operation, you should be fine.

Re: Wolverine setup

#3

Re: Wolverine setup

GalenV in Iowa

>I think the manual on mine says 6 1/4 minimum and also shows 6 1/2.

Mine is at 6 1/2" and brackets just clear my guard on 8" wheels.

The plateform when set level is like 3/4" below the ceterline of the wheel and I wish it were a little higher as it makes some grinding easier if on centerline for me.

If you use 7" it will mean the plateform will need to be set really steep to grind something like a skew. You might hit the back side of the platform to the wheel.

Just mock it up and see if using the platform will work for you.

Depending on how you grind your gouges the Varigrid may hit the wheel at some settings. Again just mock up and see. May have to adjust the stickout to get Varigrind clear of the wheel.

Since every grinder is somewhat different just going by mine.

Galen

Re: Wolverine setup

#4

Re: Wolverine setup

BobP

>Don,

My grinder is the 8" Delta 3/4 HP slow speed unit (it's a monster) and I had to put a spacer under the Wolverine guide to get it at the suggested distance from wheel center. As mentioned, each grinder is a bit different and you will have to improvise. Perhaps you could slot the guard mounting holes and nudge it up a bit to get it out of the way...just a thought. As already mentioned, changing this dimension will alter the geometry of the fixtures used with the Wolverine system. I think the vari-grind fixture will be the one to watch. It is adjustable so it just might work OK.

You might want to give Oneway a call and ask them if it is any big deal to have the distance be 7"...they would know best.

Great system. I wouldn't be without mine!

BobP

Re: Wolverine setup

#5

Re: Wolverine setup

Ron McKinley

>The critical thing here is to be grinding well above the center of the wheel. DAMHIKT! .......Ron

Re: Wolverine setup

#6

Re: Wolverine setup

Charlie Drake

>Why not just build a wooden riser in the same "vee" shape as the vee shape of the steel arm which sits in this arm and is of sufficient thickness to raise the tool the necessary 3/4 inches? Hope that is understandable.

Re: Wolverine setup

#7

Thanks for the input.

Don Orr

>I guess I'll have to play around and see what works. I like Gordon's thoughts and Galen's mockup idea. I mostly want the system for the big flat grinding rest which is WAY better than the puny little rest that comes with the grinder. But I also want to use the sliding vee arm for the VariGrind jig as well to replace my old wooden home made sliding rest which works but is kind of fussy to get set right.

Thanks guys !

Re: Wolverine setup

#8

Re: Wolverine setup

Ed in Leaside

>It really doesn't matter that much. As long as you can get the correct angles in the triangle formed by the wheel centre, pocket, and gouge tip, all will be fine. Here's a pic of mine with everything rotated forward about 60 degrees. Wheel centre is at eye level. No longer is my body in the way, and I have a better view of the action at the wheel.


img