Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

friction polish

Posts

friction polish

#1

friction polish

Johnny Watson

>I am fairly new to turning pens. Only done 10 so far, but I'm getting to like it. Can anybody lead me to a good friction polish? And maybe some pointers on how to use it? I find that I like shiny pens. The best I have done so far is Deft gloss lacquer sprayed onto a corner of a paper towel, applied to the pen wood sections immediatly while they are turning on the mandrel then "pinching" a clean towel on the wood, until it gets hot. Dries real quick and is shiny. I put on 3 coats this way. I also tried boiled linseed oil applied the same way, but don't get quite as good a shine.

Re: friction polish

#2

Re: friction polish

Al Neighbors

>Johnny, I don't know anything about friction polishes. I use CA finish on all my pens. It's easy to apply, hard, buffs really well to a supper glossy finish.

Re: friction polish

#3

Re: friction polish

Johnny Watson

>I'm a little afraid of CA. How do you keep it from gluing everything together? I have never seen it applied, so I don't know the tecnique.

Re: friction polish

#4

Re: friction polish

arkie

>Try a BLO/CA finish. Wipe on a little BLO, then add a drop of CA right to the paper towle and wipe lightly. Repaeat a few times for build up. Your friction polishes won't hold up very well if the pen is used much.

Re: friction polish

#5

Wayne K

Re: friction polish

Wayne K

>Why do you want to put a plastic coating on wood? Wood by design will gain a beautiful patina with use that will out shine any plastic coating.

If you want a plastic pen, turn acrylics and wet sand through your micro-mesh. Done correctly the shine will last.

For your woods, dry sand through your high grits, polish and wax. When you sell or give them away they will be shiny, with use the patina gained will replace the shine but give the user a well worn finish, the way wood was designed to be.

Off my soap box.

Wayne Kuhn

Columbia, MD

Re: friction polish

#6

CA finish...

Marc Phillips

>I have tried several finishes... and use CA now on all my pens. It is very durable and, once you try it a few times, pretty easy to apply.

I have a sort of tutorial (a reminder to me actually) on my web site you can read if you want...

http://woodhelp.com/Tips.htm#PenFinishing


img

Re: friction polish

#7

Re: friction polish

Marc Phillips

>To each his own for sure, but I will reapectfully disagree with you on this. If you have a pic of a pen with no finish and a beautiful patina due to natural skin oils I would like to see it... every pen I have seen with a wax or no finish just looks like it has dirt rubbed into it... and looks terrible.

Re: friction polish

#8

Re: friction polish

Dick Coers

>I agree with the CA finish. Some of my first pens had a friction polish. These are usually a shellac base and will soften at the worst, just look dull at the least. I had one returned that the finish was actually sticky. It must have been a result of hand cream or similar. No returns on the CA.

Some turners actually dip the pens in water based finish, some air brush the same. The dippers make some undersize bushings from plastic, and run a wire through the bushing. This was allow the finish to run off and not form a bead on the bottom of the blank as it hangs.

Re: friction polish

#9

Re: friction polish *LINK*

Russ Fairfield

>This link may help you get a better finish with a friction polish


http://www.woodcentral.com/russ/finish10.shtml

Re: friction polish

#10

Re: CA finish...

John K Jordan

>Marc,

As you noted on your web page, CA will react with the cellulose in a paper towel and create a great deal of heat. (don't glue a finger to such a combination! DAMHIKT)

A guy at our turning club once demonstrated using CA as a finish without this problem. To apply and spread the glue, he used a tuft of man-made fiber held in hemostats. There is no exothermic reaction with this fiber (no heat). He used bits of white fiber from the padding made for upholstery and bedding.

JKJ

Re: friction polish

#11

Re: friction polish

Sean Troy

>Russ's way works like a charm and is easy to do. I follow up his method with running through the grits of micro-mesh afterwards.

Re: friction polish

#12

Re: friction polish

John K Jordan

>>Heat is required to "flow" the finish and make a smooth finish.

Adding to this: I use Myland's friction polish and often use it without the heat of friction. I put a little on a soft cloth and rub it onto the surface with my finger. I do probably create a little frictional heat by hand, but not much. I find this method easier to get a smooth finish on larger pieces and to repair any problem areas after spinning on the lathe. For repair, I add a drop of alcohol to the cloth.

JKJ