>Looking to upgrade the live center on my Jet 1220VS. Was planning to go with the Oneway, but saw that Craft Supplies is selling one made by Precision Machinery. It seems well made and has a number of accessory tips.
>The nova live center has a lot of accessory tips but best of all is that they fit in the live center via a short #2 morse taper. This means that it's very easy to make wooden adaptors to fit almost anything. I routinely make a wooden center of a specific size to fit in holes for lamps and tool handles.
It also comes with a center that has a screw thread. This is very easy to make cone, reverse cone, or ball centers to hold almost anything.
Since they are #2 morse tapers you can put these homemade pieces in the headstock for shapeing or even on occasion use them to drive a piece.
I've had my Nova center for about 10 years and used it a tremendous amount and I've never had to replace a bearing. I think that says a lot about the quality.
It's also hollow so you can use lamp augers with it.
About the only downside is using a knock out bar to remove it. All of my lathes have self ejecting tails stocks so this isn't a problem but the hole in the #2 morse taper shank is just a tiny bit bigger than the hole in my lathe so a knock out bar sometimes won't work. This has never been a problem because the live center has a flat back larger than the tailstock quill. I simply put my skew or other wide tool between the center and tailstock body and crank it back. This ejects it quite nicely.
I've looked around for other live centers that might be better and haven't found one more versatile.
Thanks for the detailed response. I had seen another thread in which you expressed similar positive comments.
I originally included the Nova center on my list until the CS rep said that the move to Chinese manufacture had affected the quality. I'm sure with yours being older it was New Zealand made. Have you had any experience with the Chinese units?
>I have been using a Nova Live Center for about 4 yrs. I have no idea where it was manufactured but I have had no trouble with it. If the need were to arise I would buy another. I have not seen any complaints about it in the "Nova Owners" forum either.
CSUSA carries two different Nova live centers. One for $68 and the other for $100. Which one are you referring to? (The cheaper one looks like it's the better alternative -- and not because it costs less.)
>Looks like I have the $100 version (didn't pay that much). Checked the Technatool web site and it looks like the current product is the $68 version. The two versions look about the same to me other than the cone in the $68.
>CS has another live center with interchangeable tips. The tips have a short taper which helps insure that the tip is centered in the live center.
The center has a collar which uses tommy bars to unscrew and force off the tip. The threading for the collar is 3/4-16 tpi. You can get third party faceplates which are 3/4-16 tpi so you can turn any shape live center tip you like. You can also get a 3/4-16 tpi to 1-8 tpi adapter which will let you mount a turning on the tailstock so you can center the turning on a vacuum chuck.
This is not a hollow center so you can't do long hole boring with this live center. The stock Jet live center is a hollow center.
First off, the stock live center is really of pretty poor quality. The one that came with the lathe was defective. The bearing assembly would come off the morse taper everytime the live center was backed off a piece. Jet quickly sent a replacement, which wobbles and hums when engaged.
So the primary reason for me to upgrade is better quality. But since I am doing it, I wanted to go with something more heavy duty and one with the ability to change the tips.
The live center bearing on my Jet 1220 lasted about a month. I called them and they sent me a new one. Before it arrived I had gone out and purchased a new bearing for the bad one. Seated the bearing in CA as it would turn in the race. Slide out like yours.
Guess I have been living with since.
I did purchase another live center but just to get the 60 degree tip for the pen mandrel. The only store around had no new point to fit the Jets live center. Should have done better shopping but then at the time I did not know what other features I may need. The large cone being one now.
Gettng smarter by reading Wood Central (Well sometimes more confused too)