Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Glue Block

Posts

Glue Block

#1

Glue Block

Sean Troy

>Hey all, what is the best type glue to use on a glue block. Both the wood and glue block are dry. Wasn't there something about using the paper from a brown paper bag between the glue block and wood for easy glue block removal? thanks for any help, Sean

Re: Glue Block

#2

Re: Glue Block

paul waddle

>C a glue,white glue... You may use a pc of newspaper between the parts if you are making 1/2 spindles and such,but not for bowls. You need strength for bowls. Lyle Jamieson recommends a very slight concave for proper fit as its hard to get surfaces exactly flat. pw

Re: Glue Block

#3

Re: Glue Block

Greg Haugen

>For "inside out" turnings newspaper is usually place between the joints to aid in splitting the pieces on the joint lines. I've usually used "wood glue" (tite bond) for inside out turning. For a glue block to aid in chucking a piece I like to use Thick CA glue. I don't use any paper on the joint just due to the fact if I'm heavy on a cut I don't want it to let go. I want a strong hold on a glue block. After the piece is parted off, I'll square off the glue block with a 1/4" parting tool so the next time I need it, it's ready to go.

Greg H.

Re: Glue Block

#4

Re: Glue Block

Wally Dickerman in Arizona

>Sean, Newspaper was used many years ago to make the glue block easy to remove. It makes for a weak glue joint and that is not what you want. I've been using glue blocks on much of my pieces for a lot of years and I've always used med. CA glue. Yellow glue is just as good but of course you have drying time. I use accelerator, so the piece can be mounted on the lathe immediately after gluing the block.

I usually use glue blocks and faceplates in my beginning classes. I want the students to know that an expensive chuck is not needed to turn bowls.

There are 2 things that must be done to insure that the block is secure. You are making a glue joint, so both surfaces must be flat and true. If a glue block joint fails it's nearly always because not enough glue is used. With CA I apply enough glue to get squeezout after just using hand pressure.

I part the piece off by using a parting tool down the joint until I can pop the piece off with the heel of my hand. I've done this hundreds of times and can't recall losing one

Wally

Re: Glue Block

#5

Re: Glue Block

Sean Troy

>Thank you all for the help

Re: Glue Block

#6

Re: Glue Block

john lucas

>Ditto what Wally said. I use glue blocks with medium CA and accelorator for my hand mirrors. The CA with Accelorator is fragile to sharp blows which works well with my mirrors. I can put a chisel between the glue block and mirror and hit with a hard fast blow and the joint almost always breaks at the glue line which lets me reuse the glue block and doesn't damage the mirror.

to check for flatness I just use the side of my flat nosed scraper. I lay in on the piece and if I see light I take down the high spots. Goes very quickly and I've never had a failure due to that.

I've used a lot of paper joints and I don't think they are any weaker than CA with accelorator unless you don't use enough glue or you use a weak paper. I've used newspaper mostly. It was a long time before I could afford a chuck so I did this method a lot. I did run a test on weekend and tried all sorts of papers because I heard you had to use brown paper. It didn't matter as long as you used enough glue. The only exception was water color paper which was so strong you could damage the wood if you had a thin area in the spindle.

Re: Glue Block

#7

Steven Antonucci

I use 5 min epoxy

steve antonucci

>Never lost one...

The bag is only if you are concerned with saving the last millimeter of wood. I plan to part 1/8" to the side of the epoxy line...

Steve