Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Piercing

Posts

Piercing

#1

Piercing

Cagey59

>Here is the Black Locust bowl that I pierced today. Thanks to John Lucas, Ruth Niles and Charlie Belden for the advice. I did drill a series of holes in 3 rings around the area to be pierced. They weren't enough and additional holes were drilled with the burr that I was using. It went pretty well. Just one oops where the burr drifted into an adjacent area. You can probably find it in the picture.

It has just one coat of still wet natural Danish Oil.

Any tips on getting the oil on the edges of the piercing? It's rather messy trying to do it with a rag or brush.

Any other comments or critiques are welcome.

Ken


img

Re: Piercing

#2

Re: Piercing

Cagey59

>Looks like I need some advice on how to post pics too!

Ken

Re: Piercing

#3

Re: Piercing

John K Jordan

>Make your picture bigger.

Resize so your picture is perhaps 600-800 pixels across. Then save as JPG with a "compression" or "quality" value so the disk size is somewhat less than 80k. This step may take several tries with most software.

JKJ

Re: Piercing

#4

Re: Piercing

john lucas

>Very Nice Ken. How long did it take to do the piercing. Inquiring minds want to know. :)

Re: Piercing

#5

Re: Piercing

cagey59

>Using the Dremel with the flex shaft and a 1/8" carbide burr it took about 2 hours, in 3 sessions. You were right John a break is necessary.

I'll try to post a better picture tomorrow.

Ken

Re: Piercing

#6

JL

Pipe cleaners.

JL

>They allow you put oil in the most interesting places. DO NOT stick the pipe cleaner back in the bottle of oil - have a secondary container (i.e. old test tubes). I've used them to apply oil to turnings and where tenons go into mortises.

Re: Piercing

#7

Don't use Q tips-they leave lint

john lucas

>

Re: Piercing

#8

Re: Piercing

Ruth Niles

>That came out beautiful, Ken. I'd like to see a bigger picture but it sure looks nice.

Re: Piercing

#9

Re: Piercing

don lewonczyk

>If you want a total and complete uniform coverage, pour your oil in a tray deep enough and big enough to handle the edge of you piercing. Dip and swish the edge and rotate it like looking for a leak in a tube in a tub of water. After you are satisfied that all the holes are penetrated set it on a rack like a pie cooling gismo to drip out most of the excess. Using a lint free rag wipe down what's still hanging on. Using low air pressure and the rag as a back up on the opposite side gently blow the oil out on to the rag. You will have to go back and wipe down the spots of oil that comes out of the grain but it doesn't take all the much time and isn't complicated. I let the oil sit in the tub to settle and reuse it by pour it back into the orginal container, yep I can hear everyone screaming you don't do that, maybe so if you only use the oil a couple of times a year but I've been doing it for 17 years and havn't seen any effects to change my mind. Most important, get rid of the oily rag and what ever you let it drip on so you don't have a fire. Hope it helps someone. DonL

Re: Piercing

#10

Re: Piercing

Cagey59

>OK, let's try posting a picture that is a little bigger.

I am using Adobe Photoshop Elements on a Mac and am not fully aware of how to use it. If this doesn't work I will need more advice.


img

Re: Piercing

#11

Very nice close-up. Great job!

Ruth Niles

>

Re: Piercing

#12

It worked, now I see the Boo boo.

john lucas

>On my last pierced piece I had 2 boo boo's. I was lucky and able to blend them in. You have to cut off all the little part that sticks out.

Re: Piercing

#13

Re: It worked, now I see the Boo boo.

Cagey59

>I considered cutting that projection off but thought it would make the hole look too big.

This was fun I'm thinking about what to make and pierce next.