Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Moffat Stuck

Posts

Moffat Stuck

#1

Moffat Stuck

Mark Mandell - Gone Round In Jersey

>One of my moffats will not release from the mount. Can't figger out why. The ring moves fine and the two ball bearings move out, but the thing won't release.

Anyone else have this problem? If so, wha dija do?

tia

Re: Moffat Stuck

#2

Mark, I think I pried it off ...

Ed Moore in SW Virginia

>with an old screwdriver when one of mine stuck. Some WD40 may have been applied too. I may have slipped an old chisel in under the ring to get it started and used the screwdriver on the other side.

Keep in mind however, my brother's nickname for me when we were remodeling Mom's house was "El Toro" and I stayed away from the china closet. I couldn't get a bookcase down some stairs so I took my chainsaw and shortened it.

Ed

Re: Moffat Stuck

#3

How'd you get your moffat stuck?

Mike Jones, Redding, CA

>I've never gotten my moffat stuck, so can't help you there. How did you get your moffat stuck? Maybe you can reverse the procedure???

(What's a "moffat"?)

Re: Moffat Stuck

#4

I hate it when my Moffatt gets stuck....

Michael Stafford

>

Re: Moffat Stuck

#5

Depends Where It Gets Stuck

Ken Oakley-Sunny St. Cloud, Fla.

>I am not sure if I have one because I am not sure what it is.

Re: Moffat Stuck

#6

Is a lamp? With ball bearings!?

Adrien

>

Re: Moffat Stuck

#7

Moffatt Is . . .  *LINK*

Mark Mandell - Gone Round In Jersey

>


Here

Re: Moffat Stuck

#8

re: Pried it off ...

Mark Mandell - Gone Round In Jersey

>Been trying that, but no dice. Seems like something is burred. Fitting turns ok, and the ring retracts fully but will not come off the post. Had to cut the screws off under the mounting plate. If both ball catches are free (as they seem to be) the barrel should just slip off the post.

Back to the bench!

Thanks

Re: Moffat Stuck

#9

Re: Moffat Stuck

Carole Valentine

>Never gotten mine stuck. My problem is it won't stay put. I get the impression that that little knurled knob is supposed to push against the little bump and keep it from turning, but that's a joke. Maybe I am not doing something right.

Re: Moffat Stuck

#10

I did not know women had Moffatts....

Michael Stafford

>Of course there are lots of things I don't know about women...

I thought that the lamps would more or less stay where you put them also Carole. I found out that they moved around in the breeze from my high velocity fan which I use during hot weather for air conditioning. (Oh, how I want to be able to use my fan.)

I think the problem with it being stuck on the post is related to dust collecting in the locking collar. Of course when you have a stuck Moffatt you just never know...

Re: Moffat Stuck

#11

Re: Moffatt Is . . .

Ken Oakley-Sunny St. Cloud, Fla.

>OK. I have one with a magnetic base and flexible metal neck on it stuck on my bandsaw. I always thought it was a Goose Neck Lamp.

Re: Moffat Stuck

#12

Denis Putland

Re: Moffatt Is . . .

Denis Putland

>some thing that I have for breakfast every Sunday Morning. Use a wee bit of oil in the pan and you will never have to pry it off.

Denis

Re: Moffat Stuck

#13

Re: Moffatt Stuck

bob elliott

>Mark,

I picked up a Moffatt business card at a trade show. If all else fails, try this:

Bryron Stee, Moffatt Sales Manager

bstee@moffattproducts.com

business: 605-886-5700

customer service: 800-346-0761


img

Re: Moffat Stuck

#14

Website

Mark Mandell - Gone Round In Jersey

>E-mail sent to customer service. I'll see what they say.

thanks

Re: Moffat Stuck

#15

Me too

Harvey Meyer in Atlanta

>I'm stuck too. Unbolted from the lathe and drizzled some penetrating oil into where the 2 parts should separate. I have another one that is newer and isn't stuck. It has a fairly thick coat of grease on the mating parts that clasp together. I'll be interested to see what they say.

Harvey

Re: Moffat Stuck

#16

Me too Carole.

Jennifer@Indy.USA

>I can't mount the magnet vertical or the lamp would hit the floor. It really limits where it can go on my lathe.

:(

Re: Moffat Stuck

#17

Re: Me too Carole.

Carole Valentine

>Yeah, I only have one place that I can put it and that's with the magnetic base on the steel stand with half of the base under the ways. Is there something wrong with ours, do you think?

Re: Moffat Stuck

#18

Re: Anyone also have the switch fail

charlie belden

>I've got two of these lamps with a pair of mounting thingees on my lathe bench and a pair of them mounted on turned things that fit in the dogholes in my workbench.

One of my lamps has an intermitent switch failure. Won't turn on, despite changing bulbs, blowing everything out with compressed air and the old stand by - wack it a few times. Sometimes after a week or two of not working, and not having done anything in between - it starts working again.

Suggestions?

Re: Moffat Stuck

#19

Re: Anyone also have the switch fail

don lewonczyk

>I have one on a weighted adjustable steel stand that I picked up several years ago at a flea market for $3 bucks. The disconnect is stuck on it also but since I move the light to whatever tool I'm using I didn't want to screw it up by fiddling with it. I think some WD-40 and some soaking time and a little jiggling from time to time and then using two prying devices 180 degree apart and catching on the outside rim of the locking collar only and having someone pushing the conector down should allow the locking collar to release, oh, and holding your mouth just right should do the trick. DonL

Re: Moffat Stuck

#20

Switch

Mark Mandell - Gone Round In Jersey

>You switch hasn't failed, Charlie. It's merely become uncooperative.

Look up your local exorcist.

|;-}

Re: Moffat Stuck

#21

Re: Anyone also have the switch fail

Don in Ellensburg,WA,

>You can purchase replacement switches for about 8.00 each

I have done it twice with the three I have in my shop.

email me and I will look up the supplier who has them in stock verus all the others who will have to order them from moffat.

The Manf was great in getting me the part nr,and a list of possible sources. Yes two screw drivers and some we-40 gets them off the studs.The switches only took a few minutes to replace.

Next time around I will order the dust cover that is available for the switch.

Don

Re: Moffat Stuck

#22

We Are Not Alone

Mark Mandell - Gone Round In Jersey

>Called and spoke to The Man (Dave Moffatt himself) with my issue. Seems as though they are having a problem with Zinc. The retention ring knuckle is a zinc casting and is fine, however they put a zinc plating on the mounting post and, ala birds and feathers, the two parts have been tending to fuse. New posts have a teflon coating that works much mobetta.

Bottom line is that he's sending me a new mounting to replace the one I'm about to destroy, and if, per chance, the gooseneck casting breaks, I'm to let him know and he'll just send me a new light.

Now THAT's how you spell "service & support".

Re: Moffat Stuck

#23

Public Acknowledgement

charlie belden

>Thanks to Don, I now have TWO replacement switches. McMasters part numbers sure make placing an order quick and easy. Had them in hand in two days. AND - they looked for a dust cap for the switch - and called me back to say they couldn't find anything that would do the job. Now THAT is customer service.

The great thing about forums like this is there are so many helpful people. Don's a good example. I had a problem and didn't know where to look - and he solved the problem.

Re: Moffat Stuck

#24

Re: We Are Not Alone

bill Crommett

>I am not alone ! Tonight I learned what a Moffatt is.