Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Hand Scrapers

Posts

Hand Scrapers

#1

Hand Scrapers

Richard R. Steussy

>First, to follow the thread I just read--Personally, I'm deathly afraid of hollowing tools. The only time I tried them I had the "catch" of my life! (No, it wasn't a fish) I will stick to open nested bowls--much safer.

My subject here is hand scrapers. I was introduced to them by Malcolm Tibbetts in a demo he did in Sacramento. I found them to be wonderful tools for finishing the inside of nested bowls or to smooth the surfaces of platters I make.

On platters, I use only the Sorby heavy-duty scraper. The gouges are to aggressive for me. After I get the platters shaped to where I want them with my Sorby, I take the hand scrapers and go to work. When they get dull, you just hit the 60 grit grinding wheel and you're back in business. No need to burnish the edge--they're ready to go. (by the way--you never get "catches" with them)

On nested bowls, I grind the hand scraper to the shape I want and use it to get all the excess roughness left by the bowl gouge and the Sorby. I go then directly to the sanding--80-100-120-150-220-320--and I'm ready to sign my work and wax it. Dick (bowlsaw.com)

Re: Hand Scrapers

#2

Re: Hand Scrapers

Don Orr

>Do you use them with the lathe running or off. I would be very concerned about using them on a spinning piece.

Re: Hand Scrapers

#3

Re: Hand Scrapers

Richard R. Steussy

>Don--I've never had any problems using them on a moving target. The only time they can get away from you is when you get too close to the center of your piece. I've never felt threatened by them. If you are concerned, just wear gloves, as all that could happen is you could cut your hand. Never had anything close to that happen to me. Dick

Re: Hand Scrapers

#4

Re: Hand Scrapers.....80 grit?

Ruth Niles

>Richard, if you use the Sorby (or whatever) scraper for the bowl, you should be able to start with 220 grit and eliminate a LOT of sanding, and you can go right across the very center of the bottom with no problem. I'd rather get a better finish with the tool than do so much extra sanding.

Re: Hand Scrapers

#5

Re: Hand Scrapers

Mike Jones, Redding, CA

>A while back, I was at a loss with what to do with a hollow form that I wanted to have an interior finish and that had gone out of round. A cabinet scraper eliminated the need for a lot of coarse grit sanding. I used it both stationary and with the piece spinning, my hand up to my wrist inside the form.

I have also used it when dealing with wood that has both soft and hard grain areas which cause an uneven, (even if smooth) surface. These tools are inexpensive and worth having around and toying with.

Re: Hand Scrapers

#6

Re: Hand Scrapers.....80 grit?

John K Jordan

>>you should be able to start with 220 grit and eliminate a LOT of sanding

I recently made a bowl from red oak and smoothing with cabinet scrapers, I was able to skip all sandpaper up to 400.

JKJ

Re: Hand Scrapers

#7

Cabinet Scrapers

Ron in Drums PA

>I use cabinet scrapers, both inside and out of turnings. I get a much better edge with burnishing than what a 60 grit wheel can do to raise the edge.

Re: Hand Scrapers

#8

Re: Hand Scrapers

john lucas

>I think we should post a warning with this thread. Using a cabinet scraper with the lathe running can be very dangerous. I can be done with proper presentation of the blade. On the outside it isn't too bad but on the inside it could really do some damage to your hand and arm if you get a catch. It also gets very hot.

I tend to use them now for just cleaning up areas with torn grain that don't respond to cutting with the gouge. I use them with the lathe off.

With todays cutting techniques they aren't needed as often. If you have torn grain you can usually get rid of it by first lubricating the wood, I use paste wax. Then try presenting the tool at a different angle and increase the speed of the lathe or slow down the cutting speed. If this doesn't work try shear scraping with the lower wing of the bowl gouge or a freshly sharpened scraper held at a shear angle.

There are several things you can do with different grinds to improve the cutting action. I'll have to try and produce a video to show you those methods because it's hard to discuss in works.

Re: Hand Scrapers

#9

Re: Hand Scrapers

robo hippy

>Personally, I prefer a heavy scraper with a fresh burr. It is easier for me to hold, and my hands are never in the way. I did have better luck with at slower speeds with a card scraper.

robo hippy

Re: Hand Scrapers

#10

Good point

Ron in Drums PA

>I run my lathe at about 50-60 rpms.

Re: Hand Scrapers

#11

Severed nerve and tendon. About 15 stitches.

Craig Daymon

>I foolishly used a cabinet scraper inside a bowl and it got away from me. A glove would not have helped a bit. It went down to the bone. A properly sharpened cabinet scraper has 4 sharp edges. If/when it gets away from you, that can be a lot to avoid.

They do work terrific on the outside and I have cut disks out of the one that sliced me and mounted them on the end of a Sorby Multi-Tool handle and that's not bad, but DON'T use them on the inside of a spinning bowl free hand!

A GLOVE WON'T HELP! (Probably not even Kevlar.)

-Craig

Re: Hand Scrapers

#12

Re: Hand Scrapers

Carole Valentine

>"with the piece spinning, my hand up to my wrist inside the form"

Mike, I really wish you wouldn't do that...I'd hate to see you written up in JL's accident database!

Re: Hand Scrapers

#13

large vs small scrapers

John K Jordan

>Several people have reported hand injuries with scrapers. From what I can gather, these have all been inside a bowl or form and since not clarified, I assume are the larger, traditional, full-sized scrapers, probably the rounded one that looks somewhat like a french curve. I think the distinction between large and small scrapers should be made.

My opinion on the safety issue: large cabinet scrapers seem quite dangerous inside a bowl, or especially, a closed form. If one gets away from you, it may be constrained between the bowl and the hand and spin like a food processor.

A small scraper is something else. The small scrapers I use are perhaps 1" x 1.5" and rounded, oval shaped. They cannot possibly catch. If dropped, they fall harmlessly to the outside of a large bowl (one considerably larger than my hand) and fly out onto the floor. I've tried forcing and dropping one repeatedly to test this.

In my opinion, the one that matters to me, the small oval scrapers can be used safely inside a larger bowl. I would never use one inside of a closed form. I would never hand-hold a large scraper on the inside of anything.

Any scraper can be used safely hand-held (without a rest) on the outside of a bowl. IMO.

However, working with powered tools always has risks. Anyone who feels uncomfortable with any technique might better do something else.

JKJ