Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

OT: Need couple short scraps resawn

Posts

OT: Need couple short scraps resawn

#1

OT: Need couple short scraps resawn

Larry In Lima

>Hello, I hang out here and read here a lot, post now and then....

Anyway, I am putting in a new 3/4" oak floor in a couple rooms of my house. I have (2) 11" x 3.25" and (2) 3" x 3.25" long "scraps" I need to get resawn to 3/8" thickness. These will be used for plugs. This doesn't have to be anything fancy, but does need to be 3/8" thick.

I hope to eventually get a decent size bandsaw, but don't have one right now. Would anyone be willing to resaw these for me and send back? These are red oak and I'll mail you the pieces, but need to get them back in the next week or 2 to finish the floor. I"ll pay for the shipping both ways.

Feel free to email me if you'd be able and willing. I appreciate it, Larry

Re: OT: Need couple short scraps resawn

#2

JL

Send me an email.

JL

>

Re: OT: Need couple short scraps resawn

#3

Re: OT: Need couple short scraps resawn

Texian

>Larry,

Do the pieces really have to be 3/8", or do you mean 3/8" minus half the saw kerf to resaw?

Re: OT: Need couple short scraps resawn

#4

Re: OT: Need couple short scraps resawn

Larry In Lima

>Yes, they really need to be 3/8" thick when finished. This is not before anything, just "hard - real" measurements. Thanks, Larry

Re: OT: Need couple short scraps resawn

#5

Just A Question

Barbara Gill, Remlik VA

>I have plugged a fair number of floors. We just cut the plugs out of regular stock and then sanded down the part proud of the floor surface when we sanded the floor.

How are you using the thinner plugs? This is a curiosity question not a critical one. :-)

Re: OT: Need couple short scraps resawn

#6

It would be quicker ...

Ellis Walentine, Host

>... and more cost-effective all around for one of us to just make a bag of red oak plugs to your specs, Larry. Why send scraps of wood back and forth?

BTW, my customary method of making plugs is to drill partway through the blank with my plug cutter. Then I press a piece of duct tape onto the faces of the plugs and resaw the blank to whatever thickness, freeing the plugs from the blank. The duct tape holds onto them and keeps them from skittering all over the shop. You get a bandsawn face on the bottoms, but that isn't an issue. This method saves you from getting plugs jammed in your plug cutter.

Ellis

Re: OT: Need couple short scraps resawn

#7

Re: OT: Need couple short scraps resawn

Larry In Lima

>Thanks for the questions, .... This is prefinished flooring, and the final product will not be getting sanded at all. By far, the easiest method overall is to plug these holes to the correct depth (3/8" plugs) Not only is it prefinished, but I want to try to do what I can to cut plugs to match the grain. I understand that if it wasn't finished, the plug part would be much easier. That just isn't the case here. Thx. Larry

Re: OT: Need couple short scraps resawn

#8

I am confused.......

Barry Irby

>Do you need these pieces resawn to 3/8" and you will use the entire piece as a plug or patch? Or, do you plan to drill a bunch of plugs out of the pieces? (Why does the size of your blanks matter if you are making little round plugs?)

Re: OT: Need couple short scraps resawn

#9

An old trick...

Ellis Walentine, Host

>I now understand your reasoning, Larry, but I still can't believe you're going to try to grain-match these things. I guess this also means that my duct-tape trick is out, because you'll have to stain and finish the plugs prior to inserting them in the floor.

One trick, though, that might serve you well would be to press or tap these in by placing a flat block over each one as you tap it home. That way it will stay flush with the surface. Knowing most floor jobs, there will be some voids under the flooring that will allow even a perfectly thicknessed plug to get set too deep. At that point, your only recourse would be to split it out with a skinny chisel or screwdriver or try to nab it with a gimlet or something.

Have you considered just gluing the flooring to the subfloor, maybe using spring poles to press it flat?

Out of the box as usual. :/

Ellis

Re: OT: Need couple short scraps resawn

#10

Re: I am confused.......

Larry In Lima

>Ah.... guys, guys, guys... You are making this more complicated than it is. I used a stop on a forstner bit, so every hole is exactly the same depth - to make it nice and "easy" to plug. The wood is prefinished, so need scraps resawn, and then I'll use the part that still has the finish (3/8" thick) to cut plugs out of. A drill press I have, and plug cutters. The "holes" in the flooring do not go all the way through, and the floor is very, very, flat.

Anyway, enough of flooring 101, and anyone help? Thanks, Larry

Re: OT: Need couple short scraps resawn

#11

Larry,

Jorge Castaneda ~ Downeast Maine

>A counter sink cutter in a taper drill bit to make the holes and a bung cutter to make the bungs is all you needed, to cut the bungs you'll need a drill press.

Jorge

Re: OT: Need couple short scraps resawn

#12

Re: OT: Need couple short scraps resawn

Larry In Lima

>Thanks anyhow. Larry