Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

no turning but lots of work in the shop

Posts

no turning but lots of work in the shop

#1

no turning but lots of work in the shop

john lucas

>I bought myself a new tool chest for Christmas and then a friend gave me another small machinist tool chest. I've spent the whole day rearranging tools and cutting pad for the drawer and cleaning the crud out of the other tool chest. I sure didn't think that would take that long. I'm still not done but it sure did need it. I even turned some little blocks to hold my chucks and jaws so they all have a place now and won't wonder all over the drawer.

Sometime this spring I'm going to completely redo where all the machines and workbench's are. There has to be a better way.

Re: no turning but lots of work in the shop

#2

Dick Hines

Re: no turning but lots of work in the shop

Dick Hines

>Now that you have your new tool chest set up it will take you days to find anything.

Re: no turning but lots of work in the shop

#3

Re: no turning but lots of work in the shop

Michael Stafford

>I actually went to the shop for about an hour this afternoon. It was too darn cold to do anything but nevertheless I cranked up the bandsaw and prepared some demo blanks for when it warms up.

I looked wistfully upon the lathe and my stack of wood deciding whether I could turn or not and decided against it. That situation will change in the near future as I have decided I have procrastinated long enough and I am going to install a propane heater in the shop so I can turn whenever I get the urge.

I like to hear about you getting organized John. I like to be organized and I use to have an organized shop but of late it is piles of this and that everywhere. When it really warms up I promised myself the shop would get a good Spring cleaning. I promised, now can I keep the promise.....

Re: no turning but lots of work in the shop

#4

Re: no turning but lots of work in the shop

john lucas

>Mike A few months ago I organized all the wood but it's still in 4 different piles. I really need to get the addition built onto the shop to hold wood and dust collectors. Unfortunately that is going to be expensive and will have to wait until we see what the economy is going to do.

Re: no turning but lots of work in the shop

#5

I'm already looking for tools :)

john lucas

>

Re: no turning but lots of work in the shop

#6

Re:Now is the time to be building John. ....

JamieD

>... With the building crash the costs of materials are down and supplies are in stock, and contractors are begging for work to keep their businesses going.

Re: no turning but lots of work in the shop

#7

Re:Now is the time to be building John. ....

john lucas

>Jamie I would love to build now but with the budget crisis we are having there are rumors of layoffs at the University. My Boss's boss says there won't be layoff's in our department. However I've been layed off twice unexpectedly over the years so I'm not gambling right now.

Re: no turning but lots of work in the shop

#8

Propane

Barbara Gill, Remlik VA

>Mike, I had a ventless propane heater installed several years ago. Before that it was a stinky kerosene. I really like the propane. I only turn it on when I am there since my shop is quite remote from the house. This past severe weather was so cold I didn't even try to go to the shop.

Re: no turning but lots of work in the shop

#9

Re: no turning but lots of work in the shop

Carole Valentine

>Mike, I put a Rinnai direct vent wall furnace in my shop and I love it. Literally SIPS gas. They installed the heater last March when I had 40% in my tank (which also runs the generator) In cool weather I leave it set on 60 24/7 and I just ran out of gas this weekend. Of course insulation is a factor...I have great insulation in my new shop.

Re: no turning but lots of work in the shop

#10

machinist tool chest. at the lathe

John K Jordan

>Putting a machinist's tool chest at the lathe has been a great help for me. I keep things like measuring tools, diamond hones, live centers, cabinet scrapers, burnishers, drills, and much more within arm's reach.

I put it on a small roll-around cabinet with drawers and raised it up a bit with a piece of plywood both to make it easier to reach and to make room for notes and things underneath.

I just realized how messy this photo looks but hey, it's woodturning!

JKJ


img

Re: no turning but lots of work in the shop

#11

Re: no turning but lots of work in the shop

Michael Stafford

>I am not going to be able to do anything about the insulation right now without a major remodeling of my shop but the heater will make the situation tolerable. If it keeps me warm so I can turn then the expenditure will be worth it.

I envy your beautiful shop. I wish I had done as you did, plan it carefully and design in the features I wanted. When we moved I had to do something in a hurry and I am paying for it now.

Re: no turning but lots of work in the shop

#12

Re: no turning but lots of work in the shop

Don wilcut

>Go ahead John, spend the money. Help the economy. Its only money.