Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Jet JWL-1220VS arrived ...

Posts

Jet JWL-1220VS arrived ...

#1

Jet JWL-1220VS arrived ...

Ed Moore in SW Virginia

>and it is on its Jet stand, ready to turn something. As has been mentioned, the light that comes with it is too short to be of value. So, I removed the light.

If you order this lathe and decide to remove the light, then I have two suggestions:

1. Remove it before you mount the variable speed box on the end.

2. Remove it before you put the lathe on a stand.

Following the lead of my friend Mark St Leger, I am going to put a piece of MDF that he gave me between the lathe and the stand that will extend back several inches, allowing for tool holes and an arm to mount my Moffat lamp. I have mounted a power strip on the stand, but may replace it with one which has a longer cord. The strip is very convenient for sanding with a drill. The locking casters will allow the lathe to be moved easily.

The lathe runs smoothly and quietly, so I am looking forward to using it. I just hope that the 3/4 HP motor is sufficient.

Ed

Re: Jet JWL-1220VS arrived ...

#2

Re: Jet JWL-1220VS arrived ...

john lucas

>Ed I agree about the power strip. I have the old Gary Sanders swiveling adaptor for my powermatic that holds a lamp and has 2 outlets. I need more because I am often running another lamp, a drill sander and the vacuum pump which is 2 more outlets than I have.

Re: Jet JWL-1220VS arrived ...

#3

Re: Jet JWL-1220VS arrived ...

Michael Stafford

>Enjoy Ed! I hope you didn't have to sell any turning tools to make room for it.

I think you will be pleasantly surprised at what a fine little machine you have there. It has limitations but it will turn to its stated capacities.

Re: Jet JWL-1220VS arrived ...

#4

Re: Jet JWL-1220VS arrived ...

GalenV

>Ed

After last postings on the Jet I went to our local Salvation Army store and got lucky to find a flexible neck lamp with identical fittings to the Jets. It was 40" so cut it back to 24" to replace the original 14". That and a few pieces of wire and I got a longer lamp for $3.99. Any longer and I think vibration would move it around. Turned a green off balance piece and light was steady.

I used square u-bolts to put a shelf on the stand lower cross member and wood saddle to set tailstock down there when turning inside a bowl.

The power strip sounds like a good idea. It would be easier to plug in sanding drill.

Soon I will not be able to move the lathe but it is all bolted if needed to take down.

Good turning to yah!

Galen

Re: Jet JWL-1220VS arrived ...

#5

Galen, I just got a power strip ...

Ed Moore in SW Virginia

>with a longer cord. Eight feet should be enough, but four feet probably wouldn't be.

Glad that you got such a good deal on the lamp. I need to get a little plug for where the old lamp was secured.

Ed

Re: Jet JWL-1220VS arrived ...

#6

Plug?

Don Orr

>Waddayamean GET a little plug-don't you mean TURN a little plug ? ;-)

Hope you enjoy the new lathe.

Re: Jet JWL-1220VS arrived ...

#7

Plug? You are right, Don, I ...

Ed Moore in SW Virginia

>should make that plug the first project for the lathe. Maybe a cocobolo ort will work.

Before I mounted the MDF board I took a small router with a rounding over bit and hit every edge. This will make it more pleasant to work around.

Now I must decide whether to mount the Moffat light directly to the board, or create a platform of two thicknesses of MDF to raise it, or even mount it on an arm that can be swung around.

Ed