Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

No turning tonight-too cold

Posts

No turning tonight-too cold

#1

No turning tonight-too cold

john lucas

>The shop was just above freezing today. I'm going to run the heater in there tonight and tomorrow to keep it above freezing. I have a chemical cabinet that keeps a lot of paints and chemistry from freezing but it isn't large enough to handle them all. I still have some gallon and quart size paint cans that I would prefer not to lose.

When the temp is this low my heaters will only keep the shop at about 40. Too cold for this southern boy to work for more than a few minutes.

Re: No turning tonight-too cold

#2

Re: No turning tonight-too cold

Sean Troy

>I just came in from my shop. I was out there less than 20 seconds. I think I'll just stay inside and poke around the forums.

Re: No turning tonight-too cold

#3

hyuk-yuk-yuk!

Mike Jones, Redding, CA

>It's sundown here, and it's still a little above 70 deg. outside!

Re: No turning tonight-too cold

#4

Re: No turning tonight-too cold

Brian Hahn in SW Wisconsin

>My garage is fully insulated and attached to the house. I just got a bottle of Mountain Dew and it had ice crystals in it.

(My garage is is for my vehicles - I don't want them to get the chills and refuse to start.)

Re: No turning tonight-too cold

#5

Re: No turning tonight-too cold

Greg Burnard

>I second that notion, -6 degrees right now and going down. We leave for Florida Wed. I hope to find some rounders down there.

Re: No turning tonight-too cold

#6

Southern Man.....

Steven Kubien

>John, I would love to be sympathetic but right now it is around -20�C. I was in the shop today for about 2 hours when it was a balmy -10.

Steve Kubien

Ajax, Ontario

P.S. I forgot to mention, I have pen order to fill and temps are not suppose to rise significantly anytime soon. Sorry, no sympathy from me.

Re: No turning tonight-too cold

#7

I just put a curse on you :)

john lucas

>

Re: No turning tonight-too cold

#8

We use hockey sticks to stock the fire here :)

john lucas

>

Re: No turning tonight-too cold

#9

Re: No turning tonight-too cold

John K Jordan

>I spent a few hours in my garage shop. About 1/2 before I turned on a little propane heater I got from Northern Tool. It has two ceramic elements and a fan for both radiant and forced air and connects to a propane tank I have outside. After 30 minutes the lathe half of the garage was plenty warm to work. The heater was about $100, another $25 for the long hose and such.

Of course, this time of year I wear longjohns, insulated Carhart overalls, and a flannel shirt.

The house is toasty with the woodburning stove. My woodshed is getting roomier inside, though.

JKJ

Re: No turning tonight-too cold

#10

Can you give me a model #

john lucas

>I'm looking to up grade my propane heater. I may be able to get a 100lb tank really cheap so I'm looking to get a heater that somehow warms me better. More BTU's or better radiant heat.

Re: No turning tonight-too cold

#11

It was 15 degrees Farenheit here...

Allen Neighbors

>in Childress this morning. It was 25 when I finally went to the shop and built a fire. Pot belly stove 10 feet from the lathe, and still couldn't get it warm enough to be comfortable. Kept the fire stoked all day, and I'll bet it wasn't 45 when I quit this evening for chow.

It's 10:30PM and it's back down to 21 outside now.

You have my sympathy, John. I hate winter.

Re: No turning tonight-too cold

#12

Re: Southern Man.....

Ed in Leaside

>So, is it time to switch from sneakers to boots yet?

Re: No turning tonight-too cold

#13

Its in the 50's here

Fog Tanner

>Just came in and it is in the 50's outside. I was rearranging my shop and was comfortable without my thermal gear - it was around 70 in there. If it had dropped into the 60's then it was time for the insulated stuff.

If I was meant to be cold I would have been born in Dallas. I think we had our annual three days of winter the other night when it dipped into the 30's. But, according to the Texas legislature those were supposed to come on Friday - so it may still get two more days when it drops down to 35-36 overnight. Be glad when Feburary and Spring gets here...

Fog

Re: No turning tonight-too cold

#14

Now Steve

Barbara Gill, Remlik VA

>it is supposed to be cold up there in the frozen North! Down here in Eastern VA 15 degrees F is just not right. :-)

Re: No turning tonight-too cold

#15

Bill Blasic

Re: Now Steve

Bill Blasic

>Haven't been down in the shop for a week due to a having a very bad cold. So the heat hasn't been on and this morning it is -6 F and I have a new low for my shop 40 F. I turned the heat on and since this cold wave is not supposed to break till Saturday I think I leave it on for a day or two and maybe go down and turn a little.

Re: No turning tonight-too cold

#16

I need more insulation.

john lucas

>I forgot to turn the heater on last night so I went out at 5 this morning. It was 2 outside and right at 32 in the shop. Near the walls it's 28. I know there wasn't a vapor barrier put up in the shop and part of 2 walls doesn't have insulation. It will be a pain to fix that because I have to remove everything I put on those walls and the panels were nailed up using a nail gun. I had to remove part of one of the walls to run more electricity and it was really tough getting the nails out.

Re: No turning tonight-too cold

#17

Brad Vietje

Re: I need more insulation.

Brad Vietje

>Hey John,

Me too ! I have no insulation and no heat near my lathe, and it's -25(F) this morning!

I end up dealing with a lot of insulation issues in the solar biz.

Any way you can drill some 3" holes and get someone to blow in some dense-pack cellulose? When interior disruption is difficult, some people find it easier, and more effective, to do a "wrap & strap", and actually remove the siding from the outside, fill the cavities as best you can, then wrap the exterior with a rigid foam board, which also helps to eliminate the thermal bridging through the studs (which matters less in a shop than a home. I'm sure even fiberglass will help, though I don't think its a good insulation choice at all.

Vapor barriers are a whole 'nuther kettle of fish, are more complicated than most of us ever thought, and the subject of ongoing debate among thermal envelope experts. I'd check with a highly-regarded remodeler or insulator to see what has worked well after years of use in your local climate. I find it a confusing issue, and all I know for sure is that the placement of a vapor barrier depends on your climate, as well as the structure of the envelope. It depends on the temperature and humidity cycles in your area, which might be quite different than somewhere else.

My shop is under all that snow in my ugly barn (taken last winter before I went up on snow shoes and shoveled off the entire roof) -- just a little something for those suffering at 70 degrees!

Stay warm!

Brad Vietje

Newbury, VT


img

Re: No turning tonight-too cold

#18

Brad Vietje

...And now the house, too

Brad Vietje

>Can't turn -- gotta play with photos instead!

BV


img

Re: No turning tonight-too cold

#19

Mr Heater, Big Buddy *LINK*

John K Jordan

>I got this on advice from another woodturner and since found two others who use one. I place it on a table about 8' away, aimed at where I stand at the lathe. After heating the room for a while on high, I turn it down to medium or low and I can feel the radiant heat while working. It needs no clearance at the back and just 6" on each side. D-cells can drive the fan but I bought the optional AC adapter. It's made to use small disposable cylinders but they would not last long and would be expensive to operate. I got the 12' hose and connect to a 20 lb cylinder outside by running the hose under the garage door. They claim up to 100 hours on one tank, but that's probably running on low. I have a full large cylinder outside the garage so I may switch to using that.

I found it a LOT cheaper to operate than my kerosene heater since kerosene fuel is so unreasonably high. In addition, it doesn't need the floor space and clearance of the kerosene heater.

Note that 40% of my garage walls and ceiling are protected by the house and I did insulate the rest a few years ago. Not sure how well it would work in a completely uninsulated area.

The rating is 4000-18000 BTU.

Model MH18B

I think it's still on sale at Northern Tool. You can read some reviews in the link below.

JKJ


at Northern Tool

Re: No turning tonight-too cold

#20

Brad Vietje

Re: Southern Man.....

Brad Vietje

>Ed & Steve,

Now let's not go crazy here.... Maybe just getting rid of the sandals will do.

The local UPS drivers in my area try to out-tough each other, and wear shorts until Christmas -- and we had -16 (F) in December! Yowza!

Stay warm,

Brad Vietje

Newbury, VT

Re: No turning tonight-too cold

#21

I'm so glad I live in VA

Carole Valentine

>Yeah, it's cold as far as we are concerned (teens and single digits), but at least we don't have to live in a house that Mother Nature has turned into an igloo! No wonder you guys have "Mud Season" instead of Spring!

Re: No turning tonight-too cold

#22

Brad Vietje

How's that guest room coming???

Brad Vietje

>Fog -- you funny.

I would miss 4 real seasons with snow, but escaping to a warm climate seems pretty attractive, too.

BTW: Spring does not start in February around here. We often get a solid week clear and cold (below zero at night) around mid-February. The photos of my barn and house I posted under John Lucas' thread about too cold to turn, were taken in mid-March last year, but the huge snow piles around the house looked like that well into early April!. Two weeks later, we were finding ticks while working on our Apple trees!

Stay warm!

Brad Vietje

Newbury, VT

Re: No turning tonight-too cold

#23

Brad Vietje

Re: I'm so glad I live in VA

Brad Vietje

>But just think, Carole -- wouldn't life be simpler if you could get up on the roof without a ladder? ;~)

Stay Warm,

Brad

Re: No turning tonight-too cold

#24

Fair is fair

Brian Hahn in SW Wisconsin

>The Atlantic and Gulf Coast states are supposed be hot and humid to have hurricanes...

The North is supposed to be cold and have blizards...

The Desert Southwest is supposed to be hot and dry and have forest fires...

California is supposed to have droughts, forest fires and earth quakes...

...And we all occasionally like to moan about it.

Re: No turning tonight-too cold

#25

Metal roof and snow.

Brian Hahn in SW Wisconsin

>Gotta love the way a metal roof sheds the snow. Just don't stand in the way when the snow pack decides to slide!