Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Depth drill

Posts

Depth drill

#1

Depth drill

MFoster

>I have just completed one of my larger projects that seems to take over the shop. It is a large segmented form which I posted pics of on both WOW and AAW. Wont bore you all with that. I took a day to clean up the shop and make the tools find their homes. In the process I decided to make some tweaks to jigs, and do a little more organizing. One of the things I did is sharpen a 3/8 drill that I use for a depth gauge. Even after sharpening I find that drilling into endgrain, it still want to wander off of true and winds up wobbling pretty significantly, and the hole winds up far from true center of the stock. I have a "D" drill that I made from drill rod and it does seek drill the true center but requires a start with the tailstock. It also takes longer and gets hotter. I have seen some of the pros use a drill with a handle for this function and thought I would make a handle for my drill, but with it wandering so much, not sure I want to. How do they do it?

What is your experience with the hand held drills used as a depth gauge??

Re: Depth drill

#2

Re: Depth drill

John K Jordan

>It will wander with the handle as well. A brad point drill with sharp "wings" seems to track better than one sharpened conventionally. The D and spoon and gun drills are more or less self centering.

I find my holes somewhat better if I drill at a higher speed and advance very slowly. I think this must let the inertia of the bit help keep it from following the grain as much but I might be confused.

For depth, I simply hand-hold a drill bit mounted in a handle and don't care if it wanders - it still gives the right depth even if the hole is not in the center. To get the right depth I either use the little depth stops that fasten to the drill bit or make a mark on the bit with a Sharpie pen.

JKJ

Re: Depth drill

#3

Re: Depth drill

john lucas

>Even a D bit or lamp auger will run off center. I don't worry about it for hollowing. I use a fairly long 3/4" bit with a #2 morse taper that I bought at the flea mkt. It doesn't run true either.

For vessels deeper than 8" I simply finish the drilling with my boring tool once I get there. I do have to get rid of the center bump frequently but I don't do enough large hollow vessels to look for a better method.

Re: Depth drill

#4

Brad Vietje

Please DO bore us, Mike!

Brad Vietje

>Hey Mike,

It is NEVER boring to see one of your segmented vessels -- go ahead, I dare ya -- try to "bore" us!

I have the same problems boring deeper depth holes, so I'll be glad to read whatever responses you get.

Sage spinning,

Brad Vietje

Newbury, VT

Re: Depth drill

#5

Re: Depth drill

keith zimmerman, Normal IL

>I have a 3/8" drill bit in a handle that I use to drill my starter holes. I first put a depression in the center where the hole goes so it at least starts in the center and the cutting edges can get a grip on the wood.

I never worry about centering a drill hole when hollowing, just the depth, which will be correct whether the hole is in the center or not.

keithz

Re: Depth drill

#6

Re: Depth drill *LINK*

Fred Holder

>I'm not sure that I can really add anything to what has been said already. As many have noted, it is common for the drill bit to wander when drilling into end grain.

Here is what I do, and it normally works well, I lay the skew chisel on its side and find the rotating center of the wood. I push the skew in until it is centered and is cutting a nice "V" like recess that is large enough to accept my 3/8" drill that I use to mark depth. It has a handle like a file handle on the drill and the drill is super glued into the handle. I then turn the lathe on at somewhere between 500 and 1000 rpm, align the drill shaft with the ways of the lathe bed and press the drill into the pre-cut recess. Most of the time it drills straight.

All of the BIC pens I make are drilled freehand with a 9/64" drill bit mounted in a wooden handle. Again I simply align the shaft of the drill bit with the lathe bed.

The freehand method works for me, but I do not make large hollow forms.


More Woodturning Website

Re: Depth drill

#7

Re:Bic Pens

Bob Rogne

>A friend said he had seen some turned Bic pens. I tried to find info to use this for childen or youth club demos. Is there any info you could e mail me on these?

Thanks Bob

Re: Depth drill

#8

Re: Depth drill

MFoster

>Thanks all. Guess I'll go ahead and put a handle on that drill. My technique is the same as everyone else here. I may use the D drill to get a good line going, then switch to the handled one to finish.

Mike

Re: Depth drill

#9

Best Handle...

Wally Dickerman in Arizona

>The drill grabs a bit as it enters the wood. a large knob or a pistol grip handle are the best.

Wally

Re: Depth drill

#10

Re:Bic Pens

Wally Dickerman in Arizona

>These are some pens that I made quite a few years ago. I turned a couple of hundred of them before I got tired of them and quit. They have a Bic filler. The drilled hole is 9/64th.

Wally


img

Re: Depth drill

#11

Re:Bic Pens

Bob Macgregor

>I saw a fairly detailed article by a young turner (in Hawaii?) sometime last year. I think it was Rachel Dunn in Woodturning Design in the Spring 2008 issue, but I seem to have misplaced my copy of that issue.

BOB

Re: Depth drill

#12

Re:Bic Pens *LINK*

Tommy Holmes

>There are a couple of tutorials on making pens with Bic inserts at Woodturning Online. Making Stickpens and Turning a Baseball Bat Pen are the articles. You can make any design using these as a starting point.


http://www.woodturningonline.com/Turning/Projects/pens.html

Re: Depth drill

#13

Re: Depth drill

Fog Tanner

>You can of course use one of the Anti-Torque handles made by Vise-Grip. I used one for quite a while and they work quiet well, the only problem I had was they were a two handed operation.

I use a 1/4" and 3/8" drill, often referred to as aircraft drills due to the length. I made a screwdriver type handle with a threaded insert and set screw. That seems to hold better than the superglue which eventually lets go. Not as elegant as the adjustable Anti-Torque handle, but they work.

For short distances in endgrain, I use a Ray Key 3/8" gouge as a spade drill (flute facing a little past 9:00). It doesn't wander.

Fog

Re: Depth drill

#14

Re:Bic Pens

Bob Rogne

>THANKS Wally, Bob & Tommy for Bic pen info> Kids will like those.

Bob R