Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Took up the hollow form challenge

Posts

Took up the hollow form challenge

#1

Took up the hollow form challenge

MFoster

>I think John Lucas posted the thread regarding how long it takes one to turn a hollow form. I had a ball park guess, but decided to see what it would take me. This form took me about 3 hours (5 if you count the piece of firewood described below). I did not sand it to completion, as I intend on carving and texturing it after it dries, maybe ala John Jordan. I spent time with it to get the form I wanted and work around some flaws in the sapwood that I did not want to keep. It is finished to a wall thickness of about 5/16" to allow for carving. I don't know where I could shave much time off as I tend to fuss with form. I guess I'm just slow.

The picture shows that I coated the end grain with wax, which is why I lifted it off the background paper. It was actually liberally applied. I did this to hopefully keep it from cracking. The next pic shows my first attempt. While almost finished with the hollowing, I heard a couple little pop's. I knew what had happened even before it stopped spinning. I did some quick sanding on the outside after getting the form, but nothing that would have heated up the wood. I think this happened because the wood was felled in the summer when it was really wet and sealed. It was sitting in the basement of the barn and frozen due to the temp. I think the sudden thawing of the wood in the shop and the low humidity were the factors working against me. After turning the outside shape on the second piece, I coated the endgrain with anchorseal to prevent a recurrence. Am I the only one that experiences this. I find this happens to me more than I would like, but don't know what I can do to minimize it. Anyone else have the problem?

The piece is split leaf maple and about 6"d 9"h.


img

Re: Took up the hollow form challenge

#2

Firewood 

MFoster

>


img

Re: Took up the hollow form challenge

#3

Re: Firewood

john lucas

>Mike like you I'm not very fast at hollowing. Because of that I've learned to take some precautions to prevent checking. I keep a spray bottle of water handy and spray the outside of the form periodically to keep it moist. This does raise the grain of course but the outside will need a final sanding anyway.

In David Ellsworth's book he wraps the outside of the thick portion of the vessel with plastic wrap. This keeps the water from evaporating by centrifical force (or which ever force that is).

If I leave the piece for more than a minute I put a plastic bag over it to keep it from drying.

When you get it off the lathe seal the endgrain areas with end grain sealer. Then put it in a paper sack to dry for a few days. The end grain sealer is really important if you leave a tenon on the bottom or have left the vessel an uneven thickness such as when carving is planned.

Those efforts have reduced my checks on finished vessels to almost zero. If you leave a knot in the piece or if you leave an area that was too close to the heart you will still get a check. Coat these areas very liberally with endgrain sealer of even wax.

If you turn a log with the pith in the middle (even if you remove the pith), any area that is somewhat flat (like if you just saw off a branch) will be more likely to split. curves surfaces, like a funnel, will warp and not split where a flat surface will split unless very carefully dried.

I dried some slices off a dogwood limb once by placing them in a plastic bag and flipping the bag inside out every day for about 3 months. No checks. That is a worse case scenario but gives you an idea of how to dry a vessel that has knots if your patient.

Re: Took up the hollow form challenge

#4

Re: Took up the hollow form challenge

John Jordan

>You did fine there-it's not a race. Do a few hundred and you'll cut your time in half. The shape is nice.

If you simply put the piece in a cabinet/box/paper bag for a few days, you won't have the cracking problems. The outside is drying too fast. There is an article on my website about the subject.

Keep it up.

John

Re: Took up the hollow form challenge

#5

link to John's website  *LINK*

john lucas

>


http://www.stubbylathe.com/

Re: Took up the hollow form challenge

#6

Re: Firewood

MFoster------WebKitFormBoundary0ilNAO8r+WQjjqLU

>Thanks for the help John. I have often covered or sealed pieces if I step away from the lathe for a while. I can usually get away with turning a bowl to completion and covering endgrain with wax after, but have not sealed one while turning. Guess I'll start doing so more regularly. Spritzing with water seems like a good idea too. Hopefully my failure rates will go down.