Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

pen turning problem

Posts

pen turning problem

#1

pen turning problem

Karl

>Have a problem with pen turning:

glued the brass tubeinto the pen blank, used the barrel trimmer,

set bushings and blank on mandrel,

started lathe, used gouge making very minor cuts.

blank kept stopping while mandrel turned.

Not sure if brass tube is too large or if it was bored out too much, any help appreciated......thanks

Re: pen turning problem

#2

Re: pen turning problem

Bob Trucchi

>I�ve had this happen for 2 different reasons.

The glue didn�t bond the brass to the blank. If this is the case you should take the tubes out and re-glue them. I�ve had this happen when I used CA glue. I have much better luck with epoxy.

The second is you didn�t tighten the bushings onto the mandrel.

Good luck,

Bob

Re: pen turning problem

#3

Re: pen turning problem

Allen Neighbors

>I'm still waiting for my equipment to arrive so I can turn a few pens for my family. But after watching umpteen videos, I think the mandrel nut needs to be tightened. If the whole mandrel rotates, it means that the morse taper is not getting the contact it needs in the spindle.

Other than that, I don't know what to tell you. I'll watch this thread with close interest, too.

Thanks for posting.

Re: pen turning problem

#4

Re: pen turning problem *LINK*

Dick Coers

>If it was not the glue, you have to watch how much you tighten the nut on the mandrel. Over tighten it and you can bow the mandrel. Under tighten and the blanks spin. It is a learning process to see how much to tighten. Keep the tailstock off the mandrel when you tighten the nut. Spin the head by hand and see if you are bowing the mandrel. If it seems to run way off center, loosen the nut and rotate one of the blanks slightly and retighten. Sometimes the end of the blanks aren't exactly true, even with the pen mill. If it runs pretty close to true, bring up the tailstock and have at it.

If it is a glue problem here are some other tips;

Sand the brass tube before gluing. The brass usually has some tarnish and that doesn't bond well. I bought a 3 inch diameter, 80 grit, cheap flap sander wheel at the box store. You can put that in a drill press and sand a bunch of tubes quickly. I also prefer 5 minute epoxy for the adhesive. I also use Gorilla glue and have much better luck with either of them over CA. The CA seems to wipe off the tubes as you slide them in the blanks.

Go to the International Association of Penturners if you need more help. Great bunch of pen turners!


IAP site

Re: pen turning problem

#5

Re: pen turning problem

matt overton

>is your glue older than a year? I've had this happen. New glue, no problem

Re: pen turning problem

#6

Re: pen turning problem

Grant Wilkinson

>When you say that the blank stops, does the tube stop, too? In other words, is the tube spinning in the blank = glue problem, or are the tube and blank both stopping = tightening problem.

Also, not to be obvious, but be sure that you are using the correct mandrel for your bushings. There is an A and B mandrel. If there is any play in the bushings on the mandrel, you are using the wrong mandrel for that particular bushing set/pen kit.

Re: pen turning problem

#7

Re: pen turning problem

Scott Greaves in Blackfoot Idaho

>Hi Karl,

It is likely that you just need to tighten the nut on the mandrel a touch. As mentioned above, tightening it too much can bow the mandrel, causing an out-of-round pen. One other thing you can try is to turn the speed up on the lathe. So try this: Snug the nut on the mandrel, turn the speed up, and take nice light cuts with a sharp tool!

It's very unlikely that the glue bond broke, and the brass tubes are spinning inside the blank. Unlikely, but not impossible. If you try to take the blanks off the mandrel and the brass tube stays behind, then you know this has happened. But I certainly wouldn't begin with the assumption that the glue bond broke.

Let us know how this works out for you!

Scott.