Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Segmented turning question

Posts

Segmented turning question

#1

Segmented turning question

GalenV

>Is there a book that will tell me the do�s and don�t of wood selection for segment turnings? More specifically I see a lot of wood combinations on ornaments, bowls and boxes and wonder how they are sanded and finished without contamination or discoloring light woods if the darker woods bleed. It would seem if you wipe down between sanding grits you could easily stain the light woods.

I want to glue up some thinner hardwood pieces to make some blanks for small end grain boxes. The book I have on boxes does not really give this type construction, just inlaid pieces. Any comments welcome.

Re: Segmented turning question

#2

Re: Segmented turning question

john lucas

>I have about 4 or 5 segmented books. Malcolm Tibbets book is the best and most understandable. I can't remember if he discusses the bleading problem. I had that problem when I made a Padauk and maple piece. I found applying sanding sealer before sanding and inbetween each grit was the solution. Apply the sealer gently. Spraying is best. Then sand lightly. Blow out or vacuum out all dust and then spray another coat of sealer. Sand with the next grit and repeat.

Another thing that I believe malcolm mentions but I don't know where to find the info. When you put a soft wood next to a hard wood it can get lumpy if you have to start sanding with too course of a grit. This is because the soft wood sands too easily compared to the hard wood. for this reason it is handy to pick woods that offer contrast while still being roughly the same hardness. Of course cutting cleanly so you can start with finer paper solves both the hard soft wood problem and the bleading problem.

Re: Segmented turning question

#3

Re: Segmented turning question

mfoster

>Malcolm Tibbetts' book is the best book on segmenting, in my opinion. You can mix and match woods, but it does require some special attention depending on the combinations. Try to avoid gluing a lot of oily woods together, as the oils tend to weaken the glue joint and gluing these woods together can be a bit of a challenge. Helps to roughen the surfaces with sandpaper before gluing and you can also wipe the surfaces with a solvent such as acetone to remove the oils.

Sanding presents different problems. One is the mixture of different colors as you mentioned, the other problem is the different densities.

If you really sand segmented pieces a lot that have different densities of wood, you will abrade the softer wood faster than the denser wood, winding up with depressions in the softer woods. Best cure for both problems is to do the best you can to get a clean surface off the tool. Sharp tools and shearing cuts. One trick that I learned from Malcolm, and which I was using today, is to use a cabinet scraper. A sharp cabinet scraper will help fair the curves and leave a nice surface requiring minimal sanding. You can sand pieces with different colors judiciously.

Another thing to consider is finishing. If you think a wood may bleed color (pernambuco or bloodwood for instance), it doesn't hurt to use a sanding sealer first. Dewaxed shellac is best for this.

Hope this helps some

Mike

Re: Segmented turning question

#4

Thanks for your comments!

GalenV

>I think our local Woodsmith store has Malcom Tibbets book so I will see if I can get my next trip. I did go to his web site and it has six short pdf on his construction. Some of his woods of choice, purple heart, bloodwood and hard maple, I have. I just know that with bloodwood everything turns red while I am turning!

One point he says to use a lacquer base sanding sealer between sanding grits and even use a scraper to remove prior to sanding. Another he is using Bullseye Seal Coat and not sure of its base material. The secret must be to start sealing first and no reference is given to using a liquid to remove dust, so I will try air.

With my new Thompson detail spindle gouge I can get a real smooth surface on the inside of a box and can start with 320 or 220 if I am not as carefull.

Thanks again.

I just may end up with a box of bloodwood and "PINK" maple.

Re: Segmented turning question

#5

Re: Segmented turning question

Texian

>Galen,

Before wiping or using compressed air, vacuum the piece w/ shop vac with clean filter (for maximum suction). Then compressed air or wipe w/ mineral spirits. Between grits, every time. Then maybe more sealer before next grit. I do not use it that way, but makes sense that it should work well. Stop sanding with 400 as the last grit. Finer grits make finer dust that gets into smaller places and is more difficult to remove.

Malcolm's book is available on Amazon.

Have used padauk (said to be worse than bloodwood) with maple and oak with no problem.

Re: Segmented turning question

#6

Re: Thanks for your comments!

john lucas

>Bullseye is shellac. The reason using a sealer works is that it fills in the pores, or at least partially fills them in. The wood dust sticks in the pores of the wood and colors it. Some woods like Padauk will actually stain a wood if it gets wet so blow or vacuum off all the dust.

If you brush on or wipe on a sealer coat you can carry over some of the color from the dark wood to the light wood. If you must brush do it gently and don't go back over an area. The sealer wets the area and will aid in the carry over of the color if you go back or rub it around a lot. That's why I prefer to spray.

Re: Segmented turning question

#7

Re: Spray sealer sounds best!

GalenV

>Thanks John

The spray sealers sounds the best to reduce the amount of wood contact. I found a few You Tube video on segment turning and I guess to keep them short have no mention of sealers but just show power sanding segmented bowls. I imagine some turners do not want to give away all their finishing secrets.

Galen