Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Bandsaw safety

Posts

Bandsaw safety

#1

Keith Tompkins

Bandsaw safety

keith tompkins

>The recent post concerning chainsaw/bandsaw safety prompted me to post this illustration. Many turners get into trouble when bandsawing blanks, and I believe this shows the most critical area where accidents happen. In the drawing the blade is cutting across the grain, and will cut freely. As the blade approaches the area highlighted by the red arrow, it will be meet more resistance, as it is now ripping, cutting into end-grain. At the same time, the blade is getting dangerously close to the edge. At this point, several things could happen....the blade could follow the grain, and drift outside the blank, causing the blank to suddenly lurch ahead. If your hand is in front of the blade when this happens, you are in a world of trouble. The key to using the bandsaw for cutting blanks is: Always use a sharp blade, a dull blade is an accident waiting to happen. Always plan your cuts: When I cut blanks, my left hand is already BEHIND the blade when I reach a dangerous spot, if I slip, my hand is already behind the blade, and there is no danger of cutting myself. Be sure your saw is adjusted properly, guides and tension are up to specs. Set up a "red" area, where your hands never are allowed to be in front of the blade, and never break that rule. Last, be sure your blank is as flat as possible, avoid unsupported cutting. I believe a broken blade is far scarier than it is dangerous...a broken blade on a 36" saw will scare the daylights out of you, no matter hom many times you experience it...be sure your guards are in place.

As far as chainsaw advise, keep your left elbow LOCKED, and your thumb facing down, wrapped around the handle. Never sight down the bar. Your reaction time is not quick enough to stop a kickback, a relaxed arm position, with a bent elbow won't allow you to stop a kickback. Plan your cuts!


img

Re: Bandsaw safety

#2

Bob Moffett

Re: Bandsaw safety

Bob Moffett

>Very Good Advice. Following this advice could save us all a lot of trouble.

Re: Bandsaw safety

#3

Very good advice.

Brian Hahn in SW Wisconsin

>And I really think this needs more emphasis:

"a dull blade is an accident waiting to happen"

Re: Bandsaw safety

#4

Re: Very good advice.

Ken Ward

>Thanks for taking the time to post that,you may save someone from serious injury some where down the road.

Re: Bandsaw safety

#5

You Have That Right

Barbara Gill, Remlik VA

>I have seen what could happen to a hand that met the blade of one of those really big shpyard bandsaws. A friend of mine who knew better was trying to get a piece of knarley white oak through a dull blade. The wood broke and the back of his hand was laid open as if it was filleted. He still has function issues with that hand over 10 years later.

I remember Bill's hand every time I use my bandsaw.

Re: Bandsaw safety

#6

disappearing wood

John K Jordan

>I like another key point I read once. While written for jointers, it works for any power tool: Always imagine what would happen if the wood suddenly disappeared.

Am I pushing a piece of wood with my hand in line with the blade? If the wood suddenly disappeared or split or slipped as Kieth mentioned, would my hand or even my entire body lurch forward, perhaps losing my footing?

As for broken blades on an unsupported cut (a no no no), instead of simply breaking and releasing, remember a very wide thick strong blade on a big saw is likely to jam and pinch and smash and tear with a lot of damage to equipment and body.

JKJ

Re: Bandsaw safety

#7

You Have That Right, DITTO SQUARED

John K Jordan

>>...The wood broke and the back of his hand was laid open

This happened to me recently (the wood breaking, not the injury). I was cutting a nicely rectangular block of wood as carefully as I knew how, with my hands clear, doing everything "right".

In an instant the front left lower portion of the block broke away causing an unsupported cut, the blade grabbed and slammed the front of the block down, the back went up, and the block twisted.

The blade did not break but was jammed into the block and the block smashed into the table hard enough that I had to cut it away to free the blade. It was jammed so tightly there was no way to move or release it. Of course, it ruined the $35 blade, destroyed the table insert, and could have pinned smashed fingers between the block and the table if they had been in the wrong place - I would have been unable to go for help or even reach a pry bar.

Turns out the block a mostly hidden bark inclusion which broke causing the corner to slip out and leaving a nicely curved unsupported front, almost as if I'd tried to cut a round. The same thing could have happened with another type of defect in the wood such as ring shake.

Needless to say, this educated me further on the importance of looking very closely at a chuck of wood before putting it to the blade and was a reminder to be careful about where I placed my hands.

Reenactment below, except the actual block and blade ended up more twisted and tighter against the table.

JKJ


img

Re: Bandsaw safety

#8

Re: Bandsaw safety

Don Orr

>Thanks Keith for the extra safety information. Always good to read this stuff. Let's hope this helps us all to have a Happy and SAFE New Year !

I have a kind of mantra that I say to myself when cutting anything.

"Where will it go if I slip ?" Be it my hand or cutting tool, hand tool or power tool. It has made me rethink cuts many times.

Re: Bandsaw safety

#9

Ellis Walentine

Nice illustration, JKJ

Ellis Walentine

>

Re: Bandsaw safety

#10

Re: OT- 3D software

GalenV

>John

I think you may have mentioned at one time what 3D modeling software you use. Could you identify it again?

After 2D Autocad my old work place used Solid Works and then Inventor while I went off with a structural steel design program that had 3D capability. I still have old Autocad 2000 version but did not think I needed anything more being retired. Just interesting to see your modeling show up in short time on a topic. Think my ability is fading fast.

Galen

Re: Bandsaw safety

#11

Re: Bandsaw safety

bill Crommett

>I have found that the best safety lecture is to lose part of a finger to a stupid cut.

Re: Bandsaw safety

#12

Re: OT- 3D software

John K Jordan

>Galen,

Oh no, someone should have warned you - once I get started I can't shut up.

My primary package is 3D Studio Max. I've been using it since the beginning of time (as a beta tester way before it's initial release), spent years doing daily internet tech support for Autodesk/Kinetix/Discreet, taught it to others, and used it as the basis for employment for about 15 years before I retired. (So it's the fastest thing for me!) I did modeling and animation for the Oak Ridge National Laboratory, mostly scientific, technical, and architectural projects. It was fun to see things I did on the news, the Discovery Channel and in Popular Science and other magazines.

I did a little work on the side as well, including volunteer work for the church and homicide trials for pay. (Any animated OJSimpon reenactments you may have seen on CBS news during the trial long ago were from models I made - OJs house and grounds, the condo, the bronco, goldman's stab wounds, yippee.)

I also use Sketchup on occasion, as well as Autocad, and have some passing familiarity with FormZ and some others. I find 3D in Autocad to be tedious and slow. 3D in Sketchup is fast (best snaps around) but still a bit inflexible. Max is extremely versatile and capable of high quality renderings and video. The learning curve is a bit steep but hey, invest a couple of thousand hours and anyone can be an expert! Much of what you see today on TV commercials, many movies, and video games is done with Max.

These days I rarely take the time for high quality modeling, texturing, or lighting, but it remains a great tool for quick illustrations, for figuring out things like inside-out turnings, and for designing a new chicken house.

I can test your boredom level with thousands of images, but below is a teeny sample from some work projects. Some of the larger projects took hundreds of hours of work and are detailed enough for closeup renderings. If you could stand to see a little video that's 100% animation, I did this back in 2000: http://neutrons.ornl.gov/multimedia/virtual.shtml

JKJ


img

Re: Bandsaw safety

#13

Re: OT- 3D software

Ed Karch

>Yep

dull blade

pushing

wood broke

joint of index and middle of right hand.

rejoined tendon and 6 months therapy.

three years later and the index still won't work for pointing out directions.

be carefull of that beast.