Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Vacuum Pump

Posts

Vacuum Pump

#1

Vacuum Pump

David Haywood

>I am thinking about building/buying a vacuum chucking system. The main piece of the system that I can not build is the pump. I have looked at several websites comparing prices and read some of the info from various turners. Most say to get a rotary vane pump because it is the best for the money, ie cheapest. Is it the best? Or, is their something better, or is it fine for chucking?

Re: Vacuum Pump

#2

Re: Vacuum Pump

Eddie Pacheco; San Jose, Ca.-Now in Pitt. PA

>The rotary vane pumps flow the most air, in a compact size, which is very helpful in dealing with the various small vacuum leaks that occur in holding porous woods of varying degrees. 'Gast' brand pumps seem to be the most reliable and are also more plentyful on the used or surplus market. I have a Gast pump that I use for vacuum forming and it has worked well for me. These pumps are also easy to repair as well. I have also done vacuum chucking for routing and metal machining, but not yet for routing.

Another good thing for vacuum fixturing is an accumalator or resevoir tank. This can provide you a fraction more time, in the event of a large leak, to shut off the lathe or get out of the way.

Re: Vacuum Pump

#3

Re: Vacuum Pump

Darryl

>David go here, Bill sells pumps and knows all there is to know about them. I have one of his that has been "sucking" air for over two years and still pulls 29"..

Darryl

http://www.wbnoble.com/

Re: Vacuum Pump

#4

Re: Vacuum Pump

Brian Hahn in SW Wisconsin

>For vacuum chucking, you need a pump that can pull a lot of air and go down to a "reasonable" vacuum. A rotary vane pump fills that bill.

Other styles of pumps will draw a better vacuum, but they can't handle the air flow rates needed for vacuum chucking... Unless you want to spend some real money.

A standard vacuum chucking system includes a bleeder valve to control the amount of vacuum applied to the chuck - the full vacuum capacity of the pump is usually excessive for larger chucks. A pump that draws close to a perfect vacuum is really a waste in such an application.

Re: Vacuum Pump

#5

Re: Vacuum Pump

bill Crommett

>If you are mainly interested in saving money, go scrounge up a couple od old refrigerator compressors. They work for a while, but do not last long without the oil that is found in the freon system.

Re: Vacuum Pump

#6

Re: Vacuum Pump

Bill McWhirter

>I just went through the same exercise that you are now starting. After searching the web and getting outbid on several pumps on eBay, I found Joe woodworker's site (http://www.joewoodworker.com/). I purchased one of his rebuilt pumps and an accessory kit.

The site gives a lot of valuable information, directions for setting up a vacuum chuck system and it has all of the fittings, gauges, valves, bearings, and gasket tape that you might need.

Even if you decide to go with a different brand of pump as others have suggested, Joe is still a good one-stop source for all the other pieces and parts needed for the set-up.

------WebKitFormBoundarytquxz2mF+R4GTigB

Re: Vacuum Pump

#7

Mike Peace

Re: Vacuum Pump

Mike Peace

>I just built a vacuum checking after doing all of the research. An easy approach is to get a Gast model 523 off ebay. This is the same pump sold by CSUSA and Packard for vacuum chucking. It will probably be 1/4 HP. Some are 220 V. and some are 110v. If you watch you can probably get a used 110 V model for about $100 incl shipping. Gast 522 is a an older version of the 523 that will also meet the requirements. The newer Gast 523 have built in filters. Older models require external filters. Some pumps come with them else you will have to add them. I built the whole thing for $131 including the rotary adapter.


img

Re: Vacuum Pump

#8

Re: Vacuum Pump

Mike Nelson

>Got mine at Burden Surplus 4 yrs ago, just looked, they have Gast 220v 90day warranty 54.95 can't beat that.

Re: Vacuum Pump

#9

Re: What about the actual chuck?

Paul Zerjay

>I made all mine from PVC pipe and none run perfectly true. They are close, but still have a slight wobble. How do you guys make yours?

Re: Vacuum Pump

#10

Re: What about the actual chuck?

Bill Howatt

>I drill a hole in the middle of a piece of 3/4" MDF and tap it to fit my spindle. Mount it on the lathe, true the surface, then cut a groove to fit the PVC or ABS section of pipe or a coupler. I expoxy in the pipe and then true up the outer rim before mounting the gasketing material.

Common Problem: The faceplate portion should mount tight against the spindle shoulder to ensure it is true. On many lathes this will mean opening up the the threaded area on the spindle end of the plate since the spindle threads may not go right up to the shoulder.

Bill

Re: Vacuum Pump

#11

Same as Bill but...

Mike Nelson

>... use two or three thickness of mdf glued together, use spray adhesive and glue craft foam rubber sheets to face. I have several sizes, be sure to seal mdf, will suck a lot of air otherwise.