Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Bandsaw Tuneup

Posts

Bandsaw Tuneup

#1

Bandsaw Tuneup

bowlman

>Recently I have noticed some disturbing things going on with my Delta 14" bandsaw (with riser). This thing is probably 10 years old. New tires were installed last year. But here's the problem ... with a 1/2" or 5/8" blade installed, I can't get the upper guides close enough to the saw blade. I can get the rear thrust bearing up ok, but the side cool blocks are way in front of the rear of the blade, instead of almost touching and set just to the depth of the gullet. Gullet is completely exposed. Also, I have checked for co-planar and it appears fine, but, if I tweak it to get the blade where I think it should be, something binds. Any clues?

Also, I once saw a tutorial on someone's home page that had step by syep instructions on removing the top wheel, making some modifications, etc. Something about the tilt mechanism and the upper wheel housing. Ring a bell?

Re: Bandsaw Tuneup

#2

Re: Bandsaw Tuneup

john lucas

>Is the blade tracking in the center of the upper wheel? The tilt of the upper wheel will move the blade back and forth. (I'm sure you knew this but I thought I would toss it out) If you put new tires on are they crowned in the middle. The blade will track to the high point.

Are you sure your blade guide hasn't ridden up on something so it's not perpendicular to blade? I'm guessing of course. It's probably something incredibly simple that we are missing. The riser block is pinned on those saws so I don't think it can slip and cause the upper half to be out of line with the lower half.

that's all I can think of off the top of my head.

Re: Bandsaw Tuneup

#3

Re: Bandsaw Tuneup

Roger

>Russ Fairfield,has a great article somewhere,on bandsaw tuneup.

Re: Bandsaw Tuneup

#4

Re: Bandsaw Tuneup

Frank Mutchler

>Can you post a picture? It would help me a lot.

Re: Bandsaw Tuneup

#5

Re: Bandsaw Tuneup

John K Jordan

>bowlman,

Hard to know about the guides without taking a look, but as for the "tilt mechanism" on the upper wheel, if you mean the tracking arm (the metal arm behind the wheel that is moved by the tracking screw), it can bind up in the cutout hole in the upper wheel guard. This is especially a problem if the tracking arm is bent, which is common with the stock cast arm. Mine was bent after a few years of use, so I replaced it with a very strong made from machined steel from Iturra Design (866-883-8064). If you haven't seen it, call and get their catalog which has a lot of useful information about tuning and enhancing the 14" Delta. I also replaced the stock spring with their high-tension spring.

As for the guides, is it the same whether the guidepost is raised to the maximum or near the table? (might indicate a frame problem) Are you tracking far to the front of the tire instead of in the middle? Have you checked for co-planer when the blade is under tension? Is the threaded guide block adjustment possibly binding? (mine will move the guide blocks forward of the teeth.)

JKJ

Re: Bandsaw Tuneup

#6

Michael Fortune - FWW

Jim Shaver - Oakville, Ont

>A few years ago Michael Fortune wrote a great article on this for FWW, perhaps you could look through their index to find it.

take care,

Jim

Re: Bandsaw Tuneup

#7

Check Russ Fairfield's site

Brian Hahn in SW Wisconsin

>Russ has a great tutorial on tuning up a band saw.

I have the same band saw as you (10 year old Delta 14" with risers). I changed the tensioning spring to a higher tension spring and a lot of issues disappeared. I can fully tension a 5/8" blade without problems. I got the spring from Highland Woodworking (formerly Highland Hardware). I also changed out the tensioning knob, etc at the same time. I had to put a nut (1/4" hex) between the bottom of the tensioning rod and the casting to get full motion.

Re: Bandsaw Tuneup

#8

Re: Bandsaw Tuneup *LINK*

Russ Fairfield

>Is this it?


http://www.woodturner-russ.com/Bandsaw-Tuning.html

Re: Bandsaw Tuneup

#9

Re: Bandsaw Tuneup

bowlman

>Yep! That's the info I was looking for. Looks like the upper wheel is interfering with the tilt mechanism. After Christmas I'll be tearing the old girl apart. And while I'm at it, I certainly will switch to a link belt, and, if Danta is generous, perhaps a larger motor.

To all who responded, I say "Thanks you all!". WC is simply the best place to get questions answered.

Merry Christmas to all, and to all ... good turning!

Re: Bandsaw Tuneup

#10

Re: Bandsaw Tuneup

gary clarke

>Where is a good place to buy a replacement spring for a Delta bandsaw?

Re: Bandsaw Tuneup

#11

Re: http://www.mcmaster.com/

-!-

>http://www.mcmaster.com/ has 10 pages of compression and die springs. They ought to have something which will work for you.

Re: Bandsaw Tuneup

#12

iturri

robert davis

>

Re: Bandsaw Tuneup

#13

iturri

robert davis

>iturri has all kinds of bandsaw upgrades

Re: Bandsaw Tuneup

#14

Re: Woodcraft

Russ Fairfield

>Woodcraft stores carry a good spring for the 14" Delta that is packaged by Olson. I think it was about $15.

Re: Bandsaw Tuneup

#15

Re: Bandsaw Tuneup

mpax356

>I have the exact same problem with my Delta with riser block. I assumed that there was some misalignment that might require some shimming of the riser block to get everything parallel. I will review Russ's article as well.

Re: Bandsaw Tuneup

#16

Also Highland Woodworking *LINK*

Brian Hahn in SW Wisconsin

>Highland Woodworking has an Iturra 2-1/2" spring for Delta band saws. They also have a 3" spring for Jet band saws.


Iturra 2-1/2" Bandsaw Spring for Delta Bandsaws

Re: Bandsaw Tuneup

#17

Keith Tompkins

Re: Bandsaw Tuneup

keith tompkins

>Bowlman, Make sure the mechanism that tensions the blade didn't pop apart...if you loosten the adjustment too much, it can happen. If it did,the spring will be fully compressed, but the blade won't be properly adjusted, and the wheel may be tilted as well.