Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Jet 1220

Posts

Jet 1220

#1

Jet 1220

TW Fuller

>Is it normal for the motor on the 1220 (non variable speed) to run on the hot side? After running for a few minutes, mine is heating up just to the point where you don't want to leave your hand on it for long. Is this something I should be concerned about or do these run on the warm side like the 1014's do?

Re: Jet 1220

#2

Re: Jet 1220

Greg Haugen

>From what I recall, they do run hot like the 1014's. It also depends on the speeds they're being ran at. If it sounds fine, just heating up-that seems to be normal. At least it was with the one I had.

Greg H.

Re: Jet 1220

#3

Re: Jet 1220 *LINK*

GalenV

>The question has been ask before and I think the link may be one that someone included before. Motors run hot and to the point you cannot leave your hand on it for any time.

Since I have had my 1220 for about a year I have still been concerned that due to the motor location you can have a lot of shavings build up on the motor and this can eventually lead to early failure due to heat. I try to blow off the shavings as often as I can. The build up also blocks the upper fan shroud and the fan does not put out enough air movement to keep it clear. I guess I balance the quality of the motor for what I paid for the lathe and understand it is not a high quality motor and may someday need replacing. Let it be far into the future though!


http://www.iprocessmart.com/leeson/leeson_motor_temperature_article.htm

Re: Jet 1220

#4

Re: Jet 1220

TW Fuller

>Thank you so much for your replies. After owning a 1014, I thought probably it was ok, but became concerned after another poster stated he could let his 1220 run for 5 hr's and the motor stayed cool. I just wondered what other 1220 owners were experiencing as far as hot motors were concerned.

Thanks again

Tim

Re: Jet 1220

#5

Bill Blasic

Re: Jet 1220

Bill Blasic

>Tim,

I believe that poster was me and yes I have run that 1220 VS almost non-stop for 5 + hours and if you put your hand on it you would swear that it was not running. I ran it two days ago for about 4 hours and I'm always amazed that when I brush the chips and dust off the motor that it is not even warm. Now the left bearing in the headstock does get a little warm but not enough that I have to worry about it yet and the right side bearing stays cool. This 1220 replaced 2 Rikon 12" lathes that really defined hot running. Replaced the bearings and I believe they are running fine with their new owners but I know what your talking about as far as heat from the motor. The 1220 VS is a great lathe as far as I'm concerned.

Bill

Re: Jet 1220

#6

Re: Jet 1220

TW Fuller

>Bill

Thanks for your reply. I failed to note in your post that you have the variable speed model while mine is the manual model, two entirely different drives. My motor runs nice and quiet and doesn't seem to have any other issues, other than heat, so I'll assume it's normal.

I also had the left headstock bearing heating up. I backed the handwheel off slightly and now it seems to be fine.

I agree, it's a great little lathe.

Tim

Re: Jet 1220

#7

Re: Jet 1220

Jerry Whitaker

>I am in the market for a 1220 VS and I have found no difference in the price at any site I have looked at. However, it seems most outlets have a shipping price plus an extra delivery price of about $90.00 via a truck line. I noticed in the Craft Supplies Catalog, it just states a single shipping price of $15.00. I have a problem paying $90+ for shipping. Can anyone shed any light on the Craft Supplies shipping cost?

Re: Jet 1220

#8

Re: Jet 1220

GalenV

>Jerry

Craft Supplies charges by weight for the lathe as stated in their catalog and on line. You should be able to enter your zip code and it will give you the shipping to which you add the $15 addtional handling. Entering my zip in Iowa I got $24.99 plus add the $15.

Look up on Jets site and see if Jet has a local retailer in your area. The Woodsmith store I frequent has free shiping into the store. It is about a 35 minute drive one way to pick it up and I go there anyway.

I just got the 1220 bed extension AND the stand extension for the current sale price of $128.99. No shipping and they honored my woodworking club discount of another 10%!

Galen

Re: Jet 1220

#9

Re: Jet 1220

TW Fuller

>Jerry

Amazon.com is selling the Jet 1220VS model for $544.99 and the shipping is $29.99. They also have the 1220 non variable speed for

$444.99 with free shipping.

Tim