Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

handmirrors, two

Posts

handmirrors, two

#1

handmirrors, two

John K Jordan

>Wormy American Chestnut. A friend gave me some chestnut boards he had sawn from a log pulled out of a creek a few years ago. Since they were all 4/4, I thought I'd try my hand at hand mirrors. This is my second and first attempt, using some 3" mirrors I had on hand.

I think the wormholes make an interesting effect. Chestnut is rather coarse but easy to turn, cuts cleanly, and finishes up nicely. I held the blanks with just a couple of threads of a screw chuck, turned the front for the mirror, gripped the recess with expanding chuck jaws, then turned away the screw hole in the back. Thanks to John Lucas for sharing his inspirations and techniques.

(I see now I should have made a tiny adjustment in the positions for the photograph, but the upright one was balanced against the lower one and kept falling over so I just took the shot, quick!)

Note: the mirror blanks had sharp cut edges instead of nicely polished bevels, so I used a diamond hone by hand to ease the front edge. The ground glass effect doesn't look bad.

We took one yesterday to the wife of the gentleman who gave me the wood.

JKJ


img

Re: handmirrors, two

#2

Re: handmirrors, two

davidwalser

>Thank you for these examples. They're well done and will help me as I try to turn my own.

Other than speed, is there a reason you used a screw chuck to initially hold the blank onto the lathe? I had planned on using a glue block/face plate.

Re: handmirrors, two

#3

Very handsome yet antiquish looking!

Michael Stafford

>I love the reclaimed wood. It adds immediate character to the turning.

Re: handmirrors, two

#4

screwchucks and reclaimation

John K Jordan

>David, I used a screw chuck because it was handy and quick and easy! The superglue/accelerator method Sir Lucas mentioned would work fine, as would double-sided tape directly on a faceplate, or even turning a short tenon for a compression grip if the wood was thick enough. You could even glue a thin round disk on one side and grip it just like a tenon, then turn it away. The non-screwchuck methods permit more options when shaping the back since you don't have to turn away the hole, but I kind of like the look of the depression in the back.

Mike, I'm not sure it would be called "reclaimed" wood since although the log had been laying in the creek for decades, the wood was actually green when sawn from the log. (Well aged but green, kind of like me at turning boxes!)

JKJ

Re: handmirrors, two

#5

Re: handmirrors, two

john lucas

>John Those are really nice. I cut up the chestnut you sent last night so I can make my version of the those mirrors. man that's pretty wood. Really light. I assume I will have to use sharp tools to cut it cleanly.

Re: handmirrors, two

#6

Re: handmirrors, two

Allen Neighbors

>Well done mirrors! I've never turned any, but someday I might get up the nerve. I'll bet the lady liked your gift.

Re: handmirrors, two

#7

Re: handmirrors, two

John K Jordan

>Alan, Go for it - they were easy. Probably the hardest part was making sure the edge hole for the handle was straight, but I drew a center mark then lightly clamped the finished body between two small pieces of wood in my drill press vice to hold it vertical.

The great thing about these is 4/4 boards are easy to come by in a huge variety!

JKJ

Re: handmirrors, two

#8

turning chestnut

John K Jordan

>John,

I hope you like the chestnut. It turns easily without fuzz or tearout. An old article in FWW (reprinted in their Wood publication) attributed this to the natural brittleness of the fibers which tended to break off at the surface instead of pull out. "Machines well" is usually listed as an attribute in wood usage references.

One thing to watch for is chestnut tends to be weak along the growth rings, not exactly ring shake, but similar. This wouldn't matter much for the mirrors but wouldn't hold up well carving thin cross-grain sections.

Ralph Watts here has some large chestnut beams he may sell or be willing to trade if you find you'd like some bigger pieces.

I can't wait to see what you come up with. I'm going to try one with the 4" mirrors tonight or tomorrow.

JKJ

Re: handmirrors, two

#9

Re: handmirrors, two

john lucas

>Here is my mirror drilling rig. It doesn't have to be this fancy. I used an L shaped jig with 2 boards glued 45 degrees to it to help hold the mirror. Then just clamped this jig to the drill press with a couple of clamps. Then clamped the mirror with a clamp with soft jaws.

My new jig speeds put the whole process and has a padded jaw to hold the mirror. It's also micro adjustable so it's easier and quicker to center the bit.

The table on my drill press has also been pinned so it can't move. I drilled 1/8" holes in the bottom of the teeth in the rack gear and drove a roll pin in. The table won't move left and right now. If I need it to move I simply drive the 3 pins out. They fall down the column and are easily picked up with a magnet. When I finished with the shifted table I simply drive the pins back in.


img

Re: handmirrors, two

#10

Re: handmirrors, two

Bob Macgregor

>I wonder if it would work as well to drill and tap a set screw hole in the rack above the teeth and in the trough between teeth about halfway down.

Re: handmirrors, two

#11

is that a Forstner bit?

John K Jordan

>

Re: handmirrors, two

#12

Re: is that a Forstner bit?

john lucas

>John It is a Freud bit that sort of resembles a Forestner style. Quite often the hole in my mirrors are offcenter so the point may not engage the wood first. The Forestner style will still cut these holes.