Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Nested Bowls

Posts

Nested Bowls

#1

Nested Bowls

Richard R. Steussy

>I just made 2 sets of nested Walnut bowls in less than 2 hours with no setups and no problems with a hand-held tool I designed. I'm just an amateur and didn't want to buy the McNaughton for the few bowls I make and that's why I created my own system. I believe that there is a lot of talent out there that could do the same thing with woodturning problems. For example--how do you center your platters on faceplates--do you use the circle center and zero in with the tailstock or is there a better way?

Re: Nested Bowls

#2

Re: Nested Bowls

arkie

>How big and how many bowls per set?

Re: Nested Bowls

#3

Re: Nested Bowls

Richard R. Steussy

>I cored a 4" bowl out of the 6" bowl blank and a 3" bowl out of a 5" bowl blank. They were a pleasing shape and not "dumpy".

Re: Nested Bowls

#4

Re: Nested Bowls

john lucas

>Richard I mark the center of the platter and bring up the tailstock and put the point in that. Then I just slide the tailstock up until the platter sits against my vacuum chuck, turn it on and start trueing everything up. I pull the tailstock away when it gets in the way.

You could just as easily put a wasteblock in the chuck or faceplate and put CA glue on it. Then move the platter into position.

I prefer to do the frontside of a platter first if I don't have a plan because I want to see the grain and possibly move the platter after making a few cuts to center everything up.

On production platters I do the bottom first and turn a rebate for the chuck. Once the bottom is finished I turn it around and do the top.

Re: Nested Bowls

#5

Re: Nested Bowls *LINK*

John K Jordan

>Frank Penta has an article on turning platter bases that might be useful.


Frank Penta on platters

Re: Nested Bowls

#6

Re: Nested Bowls

Richard R. Steussy

>One further question on platters--why turn a 2" thick piece if you can use a 7/8" piece and add a separate foot piece. If it's contrasting, doesn't that make an attractive platter? Of course, it's not as professional, but I'm a utility-type turner and I'm thinking of the use of the platter--and the result still has that "floating" look.

I've taken a 16" platter round of 7/8" cocobolo (either solid or glued-up) and mounted on it a 5" base of maple for contrast. The problem I had was after I turned the foot to the shape I wanted--how did I get it to center on the platter body? My solution was to carve a 5" groove for my chuck in the face of the platter stock, (using a MDF blank faceplate with hot-melt used sparingly) then peel off from MDF and reverse and mount on chuck. I then could work the base side to create a small area for the maple foot to sit and on which I mounted it. I brought up the tailstock and placed it in the center of the foot and glued it to the platter body with Titebond, using the lathe as the clamp. Then, after I'd turned the base of the platter itself, I could turn it around and use the foot (which I had grooved for my 5" chuck) to finish the face of the platter. Does this sound like the best solution? I'm open to suggestions.

Re: Nested Bowls

#7

Re: Nested Bowls *LINK*

Rick Allen

>I am not a big fan of the foot being glued onto a platter. First it always looks like the foot is glued on and second the foot is likely to move differently than the platter body as the wood expands and contracts with the seasons. This expansion thing is especially evident when the woods are different species.

I make platters out of 4/4 stock all the time (that works out to 7/8 when the rough part is cut off).

Procedure:

Mount the platter stock between the chuck jaws and the live center. I like to use a cup center in the live center so the deforming of the wood by the point of the live center is minimized.

This will be the bottom of the platter.

Make the platter blank round and true.

Cut an 1/8" long tenon on the tailstock side to fit the chuck jaws in compression.

Mount the platter on the chuck and bring up the tailstock as before.

Turn as much of the platter as you can without moving the tailstock. It is important to work from the rim towards the center an inch or two at a time. This is to say that the outer most inch or two of the platter should be finished both top and bottom before turning any of the center wood away.

Keep doing the a little at a time till your cuts will all occour within the jaws of the chuck. This is to say that is your chuck jaws are 3" across then the tailstock and live center should be supporting the platter until you are cutting the inner most 3" of the platter.

I use an engineers square to guide me while flattening the inside bottom of the platter.

Keep in mind the 1/8" of material that was cut out of the backside for the chuck. I use calipers often to check my progress.

I use cole jaws to turn away the tenon on the underside of the platter and to refine the foot of the platter.

I use a 5/8" (American measure) bowl gouge for all the turning except for a little dressing up of the rim/body interface where I use a variety of small tools depending on the shape.

I have a small article on my web site about making a platter which primarily follows the instructions above.


Making a platter

Re: Nested Bowls

#8

Re: Nested Bowls

Ron McKinley

>Good tutorial. Thanks for sharing......Ron