Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Attn: Steve Antonucci. Burner Quest.

Posts

Attn: Steve Antonucci. Burner Quest.

#1

Attn: Steve Antonucci. Burner Quest.

Allen Neighbors

>Steve, I built my Charger Burner Pen like yours in the pic you posted.

My battery charger isn't as powerful as yours, and I'm wondering what will happen if I shorten the 12 gauge (heat sinc) wires a little, and how much to shorten them.

Will it put more heat into the pen tip? Will it take less power from the charger?

Thanks in advance for any info you can share.

This pic is the burner. Notice the amperage of the charger is only 6 amps total, so it's not as big as yours. The second pic is the pen tip.


img

Re: Attn: Steve Antonucci. Burner Quest.

#2

Pen tip

Allen Neighbors

>This is 16 gauge wire. I have a Molly Winton pack on order, for some lighter weight wire.


img

Re: Attn: Steve Antonucci. Burner Quest.

#3

Re: Pen tip

bernie feinerman

>Shortening the length of nichrome wire will increase the power drawn from the charger and increase the heat in the tip.

Shortening the 12 gauge copper "heat sink" will not get you any significant increase in power. It just will move the heat closer to your "handle".

Using a smaller gauge (larger number) nichrome wire will decrease the power drawn from the charger. If you go to too small a gauge of nichrome wire it may not get hot enough and will be physically more fragile.

Can you change the tip design to use less length of nichrome wire and get the same burn effect?

Re: Attn: Steve Antonucci. Burner Quest.

#4

Re: Pen tip

Allen Neighbors

>I can't change the tip, other than to shorten the legs, until I get my order of smaller gauge wire.

Thanks for the information. Duh! I should have known that shortening the 12 gauge would move the heat. :)

I guess I'll just have to wait for some smaller wire to get here.

Re: Attn: Steve Antonucci. Burner Quest.

#5

Re: Pen tip

bernie feinerman

>American Science and Surplus in chicago is another source of Nichrome wire - (they have a web site).

Your 2nd pic looked as tho you were geting plenty of burn marks. If the charger is getting too hot perhaps a fan cooling the charger might help.

Re: Attn: Steve Antonucci. Burner Quest.

#6

Re: Pen tip

Allen Neighbors

>It did shut off a time or two for about 30 seconds or a minute, but clicked back on. I had it turned up til the tip was red hot to the point that the wood flamed up as soon as the tip made contact.

Just enjoy trying out different tips. :)

Re: Attn: Steve Antonucci. Burner Quest.

#7

Re: Pen tip

John K Jordan

>>I guess I'll just have to wait for some smaller wire to get here.

If needed, you can make thicker wire into thinner wire with a file, perhaps just at the tip.

JKJ

Re: Attn: Steve Antonucci. Burner Quest.

#8

Re: Attn: Steve Antonucci. Burner Quest.

Jennifer@Indy.USA

>Allen that looks like a great set up. Fire away!

Jennifer :)

Re: Attn: Steve Antonucci. Burner Quest.

#9

John; Jennifer;

Allen Neighbors

>Thanks for the advice, John, I did that to the writing point, but I want a coil, to make a basket weave pattern, and it'd be hard to thin a coil. :)

Thanks, Jen, when I put some of that 24 gauge on there it does fire up!! :) I really appreciate all the postings about this charger/burner idea.

I've done a couple of little Southwest forms with a 5/8 wide band of basket weave, but with that 16 gauge it's like trying to write with my WallyWorld burner... sloooowww. And as shaky as I am, when I tried a coil of the 24 gauge, it was a little limp for me. I guess the 18 or 20 gauge will work better. But I sure do like having the heat. This thing is going to really do the trick!

Re: Attn: Steve Antonucci. Burner Quest.

#10

Steven Antonucci

I'm here!

Steve Antonucci

>Looks like most of the answers are already there. Smaller wire will get hotter. You don't need to have it glowing bright enough to emit light to burn wood. A dull red may not get the "Priddle Squeak", but it'll still burn the wood plenty so.

My charger being 10A completely fries the nichrome wire if I run anywhere near 10A. I suspect 6A is plenty, and on a thinner gauge wire, probably too much. More than the current/heat issue, the thin wire is too wimpy to actually press into the wood without it "smushing" to a ball of goo on you the first time you use it. JKJ had the right idea about using the heavier wire and filing it thinner where you need it. A little more work, but no more money...

Steve

Re: Attn: Steve Antonucci. Burner Quest.

#11

Keep a Fire Extinguisher Handy! : )

Jennifer@Indy.USA

>

Re: Attn: Steve Antonucci. Burner Quest.

#12

Re: Pen tip

DaveG

>Mine tunrs off from time to time but I always though it was because I have an automatic charger not a manual charger. Which means when the charger sences the correct amount of current it turns of so it will not damage the battery. I think I meet those conditions when I have the dimmer set just right and the charger turns off.

Re: Attn: Steve Antonucci. Burner Quest.

#13

Re: I'm here!

Allen Neighbors

>Thanks Steve.

I may try to make a coil with the 16 ga, and then run my cutoff blade for my dremel between the coils. I'd never thought of that, until John said to file it down. Then I could squeeze the coil close together again... I'll give it a try.

Thanks again.

Re: Attn: Steve Antonucci. Burner Quest.

#14

John, when Steve repeated what

Allen Neighbors

>you said, it dawned on me that I might be able to use the cutoff blade on my dremel tool, and run it down between the coils and thin them down that way. Thanks, it's your idea. I'll give it a try. Thanks again.

Re: Attn: Steve Antonucci. Burner Quest.

#15

Re: John, when Steve repeated what

john lucas

>Allen The thinner metal will get hotter so you would have to be careful to make all of the pieces the same thickness. This might not be as critical as it seems so I would go for it. You can always remake it.

Re: Attn: Steve Antonucci. Burner Quest.

#16

Re: John, when Steve repeated what

John K Jordan

>Are you creating the coil with a straight wire? I'd try to thin it with a file before coiling. But as mentioned, a thin spot will be a hot spot. A new piece of wire the right gauge would sure be a lot easier!

JK

Re: Attn: Steve Antonucci. Burner Quest.

#17

Re: Pen tip

DaveG

>Another way to make the wire thinner is to use a ballpin hammer. I saw a write up on the web somewhere where they take a section of the wire and work it with a ballpin hammer, hitting each side of the wire making it very thin. Then they came back with a file making the shape they want. I have tried it and it works very well. The only thing you have to watch out for is not turning the power up to high when there are very thin spots in the wire. If you do turn it up to high it is then called a "flash bulb" and you will need to start all over with the hammer.

Re: Attn: Steve Antonucci. Burner Quest.

#18

ball peen hammer - special wire *LINK*

John K Jordan

>The Fishcarver web site has good information.

The guy who wrote the article in the link below mentions "not all nichrome is the same. It comes in different blends for different applications. It took me years to find the perfect combination of nickel and chrome that allowed me to hammer a paper thin edge without cracking and once heated self tempers to retain the shape under pressure."

He offers lengths of this nichrome wire for sale for pyro-maniacs.

JKJ


making special tips

Re: Attn: Steve Antonucci. Burner Quest.

#19

My thanks to all

Allen Neighbors

>Thanks for all the answers, folks. Awesome forum!! I'll probably end up trying a little bit of all of it, til I find what works for me.

I have been making my coil from a piece of straight wire, by wrapping it around a small shaft of steel. I like the idea of flattening it first, and using a file, or maybe my little 1" belt sander. I'll see what I can do with it.

Thanks again, everybody! :)