Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Bending Blackwood

Posts

Bending Blackwood

#1

Dick Hines

Bending Blackwood

Dick Hines

>I am working on another box that will have , I hope, 2 blackwood rods running across the top. The rods will be running through 3 post. The middle one is a tad higher than the other 2.

Now for the $64,000 question. These rods are about the size of .5mm pencil lead. How do I bend blackwood?

Re: Bending Blackwood

#2

Re: Bending Blackwood

john lucas

>I've never tried blackwood. I bend small wood like that by wrapping them in a wet wash cloth and putting that in the microwave. It varies with the size and species and how big the washcloth is etc. A good starting point is 30 seconds. Sometimes as long as a minute. Then I put them in a form and clamp them down with rubber bands to hold the shape. You will get some spring back so if shape is critical you should run a test and see how much smaller to maker your form.

Before I used the microwave I simply put small pieces in a frying pan with water and heated it to boiling. I also have a small steam bending rig I made from a T kettle and a piece of 2" PVC with screw on caps. You need a hole for the steam to enter and one for the steam to escape and a way to hold the pipe above the kettle.

Re: Bending Blackwood

#3

Dick Hines

Re: Bending Blackwood

Dick Hines

>John I may try the wet cloth. If I was to but these rods in a 2" pipe I may not find them again.

You will see what I am talking about if this works out because I am going to post a picture.

Re: Bending Blackwood

#4

Re: Bending Blackwood

Carole Valentine

>I wouldn't think Blackwood would respond well to steam bending at all. It is so oily and dense that I doubt the steam would penetrate. You may pull it off with the tiny pieces you are talking about but I doubt it...let us know.

Re: Bending Blackwood

#5

Re: Bending Blackwood

john lucas

>I would agree with Carol if it was just steam bending but the microwaving is sort of a combination of steam and internal heat. I'll be interested in seeing if it works. I'll be in the shop on friday and Saturday. I'll cut a little chuck off a piece of ebony and see if it works. It's not blackwood but I would think the properties aren't horribly different.

Re: Bending Blackwood

#6

Torch

Jorge Castaneda ~ Downeast Maine

>I agree with Carole,

I never done it but I've seen pictures of people bending some heavy woods around the frame of a boat using a torch.

Re: Bending Blackwood

#7

Re: Torch

Carole Valentine

>The boat builders around here prefer white oak for bending. Dick, you ebonize some of that and bend it.

Re: Bending Blackwood

#8

Dick Hines

Re: Torch

Dick Hines

>I am going with the blackwood. When I decided to do this piece blackwood was what I had in mine so I am not going to give up.

If this works I will post a picture.

Re: Bending Blackwood

#9

Re: Torch

john lucas

>I've bent wood by heating a pipe and then bending it around the pipe. This is how they sometimes bend guitar parts. I had trouble controlling the heat and was bending a light wood so I had some scorch marks.

You probably have enough info now to do some tests. I forgot to tell you that green wood bend better than dry. Try soaking the wood in water for awhile and then use the wet rag and microwave

One more option that might work. Soak it overnight in ammonia. I used to bend yardsticks and tie them into a know doing that. It discolors some woods so do a test. This makes the wood really flexible. It takes a good 24 hours or more to dry so leave it in the jig as long as your comfortable doing so.

Re: Bending Blackwood

#10

Re: Bending Blackwood

Bob Macgregor

>I wonder if the output from a steam-type vaporizer might work if directed into/through a small tube.

BOB

Re: Bending Blackwood

#11

some woods just do not bend *LINK*

Tom Sontag - St. Louis

>I will be following this thread for your experiment's results, but note that many woods do not bend well. The USFS data sheets on wood properties often mention bending characteristics, but I find no mention in any of their Dalbegia (rosewood) species. (I presume we are discussing African blackwood (D. melanoxylon)


USFS on African blackwood