Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Stick Fast epoxy?

Posts

Stick Fast epoxy?

#1

Stick Fast epoxy?

John K Jordan

>Any known problems with Stick Fast epoxy?

I bought some when at JCC in August. I used it once a couple of months ago and it seemed stringy or grainy when mixed, not at all like other epoxies I've used, but it seemed to set up OK. Yesterday it was unusable - the resin had completely gelled, looking a bit like fine tapioca pudding.

Is Stick Fast not a good brand or did I just get a bad batch?

JKJ

Re: Stick Fast epoxy?

#2

Re: Stick Fast epoxy?

Chuck Engstrom

>Winter is upon us and you may be suffering no more than cold temperature effects -- where do you store it? I had been keeping my StickFast in a closet on an exterior wall and had much the same problem a couple of days ago -- not gelled but mighty sluggish and hard to get out of the squeeze jar. I've now moved it to the top of the water heater between uses, where the temp is usually about 73.

Stick your jar of resin in a pot of fairly hot water and it will probably ungel just fine. I doubt it has gone bad, since shelf life for epoxy is virtually unlimited; I am still using some given to me almost twenty years ago -- and it has been heated up several times to clear crystallization etc.

Best--

Chuck

Re: Stick Fast epoxy?

#3

Re: Stick Fast epoxy?

john lucas

>Ditto what Chuck said. I've been using the stick fast epoxy because we get it so cheap from the club. I find it hard to get out of the bottles. I keep it in a heated chemical cabinet that I use for all my paints and glues to keep them from freezing. 60 degrees is almost not enough to let that stuff flow so I often take it in and hit it with the microwave for about 5 seconds or less. Made the mistake of leaving it in there for 15 seconds the first time. That could be dangerous. the middle becomes extremely viscous and very hot. You have to let it sit for a minute or two to even out the temperature.

My goal this year is to buy a good selection of epoxy from West Systems. I want to get the various hardeners and thickeners so the intial expense will get my attention but it should last a long time and from all I've heard is a much better epoxy.

Re: Stick Fast epoxy?

#4

Re: Stick Fast epoxy?

Chuck Engstrom

>The initial expense is daunting but you can mitigate this by using syringe type dispensers to measure as little as you need without much waste -- that's one reason I'm still using stuff given to me twenty years ago. The West System pumps are fine if you're using substantial quantities in a big project but generally give you much more than needed for small jobs like filling in cracks in a turning.

I got a couple of small syringes from my vet and set them up on my little jars of System Three Clear Coat, one parked in a tight-fit hole drilled in the top of each bottle. I've mixed as little as 0.6 cc total resin plus hardener with reliable and repeatable success. In my big jars of standard S3 resin/hardener I have big syringes I bought from them, and again, I've had reliable and repeatable success doing as little as 2 cc resin, 1 cc hardener. BIG savings. Bring the plungers well back up the tube of the syringe when you set them aside for a while.

Best--

Chuck

Re: Stick Fast epoxy?

#5

Thanks

John K Jordan

>Thanks to sirs Engstrom and Lucas. Immersion in hot microwaved water did the trick. The grainy gel went back to clear liquid.

Seems odd to me that out of the six types of epoxies stored in the same place, only the Stick Fast this problem.

JKJ

Re: Stick Fast epoxy?

#6

Re: Stick Fast epoxy?

john lucas

>thanks Chuck Excellent idea. I had not thought of that being a problem. On days when I only make one mirror I don't need more than a few drops of epoxy.

Re: Stick Fast epoxy?

#7

Re: Thanks

John K Jordan

>I just got an email from the Stick Fast people with the same suggestion and an explanation:

One great feature about our epoxy is that there are no solvents in it. That is great but sometimes the resin starts to gel and crystallize. To fix that just put the bottle in some hot water and it will thin out. John Matwick-Stick Fast adhesives and accessories

JKJ

Re: Stick Fast epoxy?

#8

syringes

John K Jordan

>FYI, you can buy syringes like that from farm stores, farmer's co-op, Tractor Supply, etc. They are real cheap.

You can get nice syringes real cheap sometimes after the holidays - made for injecting turkeys with seasoning before cooking. I found some once in Walmart.

JKJ