Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Live center thread?

Posts

Live center thread?

#1

Live center thread?

Jerry Klug

>My Powermatic tail stock live center thread appears to be 20x2.5mm. I want to get a tap and tap drill to make my own center points. My Machinery's Handbook is a 1964 vintage and has little metric information. What is the correct tap drill size for a 20x2.5 thread?

Re: Live center thread?

#2

Re: Live center thread?

Gordon Seto

>The Oneway live center thread is 3/4" X 10 tpi. I believe the Powermatic is the same size. I have seen some posts that the Oneway cone fits PM; but I am not sure.

Re: Live center thread?

#3

Bill Blasic

Re: Live center thread?

Bill Blasic

>Gordon,

Is that the size (3/4 X 10) of the thread on that piece of high density plastic that you gave me?

Re: Live center thread?

#4

Re: Live center thread?

Brian Hahn in SW Wisconsin

>The recommended drill size for a 20x2.5mm tap is 17.5mm.

I'd bet that Gordon is right and it is a 3/4-10 thread.

Re: Live center thread?

#5

Re: Live center thread?

Gordon Seto

>Bill,

Yes, the tap that I used was 3/4" X 10 BSW (whatever that meant). Does that fit your PM live center?

Gordon

Re: Live center thread?

#6

Re: Live center thread?

Chuck Engstrom

>I'd suspect strongly that your PM thread is really 3/4" x 10tpi. One inch is 25.4 millimeters, so your reading of 10mm diameter comes out to .7874 inches, just a hair over 3/4", and 2.5mm per thread comes out to 10.16 threads per inch. Go to your local hardware store and get a 3/4-10 nut and see if it fits OK. If it does, 3/4-10 taps are pretty easy to come by.

5/16 and 8mm are also easy to confuse, 8mm larger by only 0.0024 in. I once worked on a Lucas diesel engine starter which, I remain convinced, had one stud of each, and I was extremely lucky to figure this out before I screwed up the threads of either by taking a wrench to the wrong nut. That would have been a several hundred dollar mistake.

BSW is Brisitsh Standard Whitworth, a British thread standard: http://en.wikipedia.org/wiki/British_Standard_Whitworth.

Best to all --

Chuck Engstrom

Re: Live center thread?

#7

Re: Live center thread?

Randy Privett

>Jerry,

One good rule of thumb for figuring metric tap drill sizes is, using your size; 20X2.5 is 20-2.5 = 17.5 X .03937 = .688975. The closest drill for that size is .687, or 11/16". This can be used for any metric size taps.

Randy

Re: Live center thread?

#8

Re: Live center thread?

John Jordan

>You don't need to tap for your custom centers. Just turn the hole a few thou under-sized, it wont take much. You want it where it just takes modest pressure to screw it on, and it will make it's own thread.

There's no tendency for them to come off. If they don't run quite true, put a piece of wire through the lock hole, and put it in the headstock to true up your shape.

John

Re: Live center thread?

#9

Re: It works for English threads too.

-!-

>The tap drill for a 1/2-13 thread is 27/64, or .4219.

1/2 (the diameter) minus 1/13 (the pitch) equals .5-.0769 or .4231. For any 75% thread, you just subtract the pitch from the diameter.

Re: Live center thread?

#10

Re: Live center thread?

Jerry Klug

>The response has been great. The reason I wanted the info on the metric tap drill size is that I assumed that the thread was 3/4-10 until I had tried a 3/4" nut on my live center. It would not thread beyond 1-1/2 threads then lock up. The 20x2.5 nut I tried easily threads albeit a bit sloppy. My cone center is a bit loose until nearly fully threaded too.

Re: Live center thread?

#11

Dick Hines

Re: Live center thread?

Dick Hines

>Jerry if you a an AAW member look at you winter 2007 journal. If not try to get your hands on one. If all else fales e-mail me and I will send you the artical.

The Oneway live center is indeed 3/4"x10tpi.

All you need to make your new centers can be had buy going to www.mcmaster.com. They have the taps, UHMW blanks and all the other orrs and ends need to do to job.

I have made 5-6 cones of different shapes.

A shfty hent. When turning UHMW stop often to clear the ribbons that get wraped around everything. They can catch a finger quicker that you can blink.

Good luck.

Re: Live center thread?

#12

Re: Live center thread?

bill Crommett

>I have made a number of cones of various sizes by imbedding a 3/4 X 10 nut into a piece of wood by epoxy-ing the nuts which I got from Fastenal tool supply. Then I cut the head off from a 3/4 X 10 bolt and chucking it into a chuck with a deep set of jaws. Some times I have to true up the cone afterwards by putting a wire in the live center to finish the job. FASTENAL sells the nuts for around $6.00 a bag of 10.

Re: Live center thread?

#13

Re: Live center thread?

mpax356

>I used one of those 3/4 X 10 tpi nuts imbedded to make chuck to hold the end of spheres on the tail stock side. I simply threaded the block of wood with the embedded nut on the live center, inserted a small nail into the hole with a piece of tape wrapped over the nail head to keep it from coming out and to keep the center from spinning thus turning it temporarily into a dead center for mounting in the headstock spindle for final shaping.

Re: Live center thread?

#14

Bill Blasic

Re: Live center thread?

Bill Blasic

>Gordon,

yes it fits, Thanks.