Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

So what's it worth?

Posts

So what's it worth?

#1

So what's it worth?

Gary Evans Tallassee, TN

>Hi all,

Thus far, I have had 613 looks at my listing in the WC classifieds for my Woodfast lathe with not a single inquiry from an interested party.

I priced it at $1500 based on an opinion that I read on the AAW website and then offered to toss in a couple of chucks to sweeten the deal. I even offered to trade for a smaller lathe with someone who wants to upgrade.

Now I'm not sure whether I've priced it too high, or whether I'm just not destined to sell it at the moment.

What do you think? How should one price an older, high-end lathe, particularly given the upgrade to a 3PH motor with Variable Frequency drive?

I'm sincerely interested in opinions,

Gary

Re: So what's it worth?

#2

Steven Antonucci

Too far to drive

steve antonucci

>No way that someone will ship it. Economy is tight, but I think you've got a fair price on it. I would have probably bought it if you were within a day's round trip.

I'd leave it unless you really need to dump it, then I bet folks come out of the woodwork. :-)

Steven

Re: So what's it worth?

#3

Re: So what's it worth?

Philip Morris

>Gary,

As you and I have discussed before, I recently downsized like you, so my opinion is not worth much. I agree with Steve that the price you set seemed reasonable.

I am sure you have tried the local Craigslist. Have you considered approaching the turning clubs within a days round trip and asking them to list it on their websites and/or in their newsletters? Just a thought.

Re: So what's it worth?

#4

Re: So what's it worth?

arkie

>The price seems fair to me. Had it been available when I bought my Nova new for about the same price, I'd gladly have bought it instead.

Hang onto it if you can. If not, pull the chucks back out and keep dropping your price until somebody can't resist.

Re: So what's it worth?

#5

Re: So what's it worth?

John K Jordan

>Gary,

I briefly considered this myself but I had too many questions and no good place to store it (which could possibly be worked around), although it is close enough to haul easily. The price didn't bother me so much although it is hard to price an older lathe, but for just a little more I could get a second Jet 1642 - I can envision several advantages to having two identical lathes. When I saw your ad, I wondered if 1.5HP was enough to turn bigger chunks of wood. Some other questions:

- Do you now when the Woodfast was built?

- Do you have a better picture? The one in the classifieds is too small to see the details.

- What's the distance between centers?

- Does the 3 phase controller you added fit somewhere within the lathe or is it in an external box?

- Does it run on 220v?

- Have you turned outboard on it for a larger swing?

- Does the motor reverse?

- Is the outboard spindle threaded normally or left-handed?

- Is the spindle threaded 1-1/4"x8, same as my Jet 1642?

- Does it have a good spindle lock?

- Indexing?

- Do you know the sizes of the through holes in the spindle and tailstock?

- Are both the head and tailstocks MT-2 tapers?

- Do you know the weight?

- Dimensions (floor length and width, height)?

- What's the height of the spindle above the floor?

- Is this lathe still being produced, and if not, can you still find parts?

- Is this the same lathe that Woodfast lathe that Rikon is selling now?

JKJ

Re: So what's it worth?

#6

Re: So what's it worth?

JohnKyler

>Sold my long bed 16" Woodfast last year for $1,800 in new like condition. It had the outboard attachment and centers.

It had the original motor (non-VF drive).

We were both happy. I also delivered it.

I would say that if you were to clean it up and take another picture it might help :)

Also I would let folks know it is 220v single phase.

JMHO

John

Re: So what's it worth?

#7

Re: So what's it worth?

wilbur

>As someone who recently went through the process of upgrading to a larger lathe, here's my two cents. I think that one of the things that is limiting interest in your lathe is that it's a shortbed lathe. That automatically will lose anyone looking for a new lathe that thinks that they might want to do spindle turning, even on occasion. Your potential customer is a turner that ONLY wants to turn bowls, or someone with a large enough shop to accommodate two separate lathes, should they want to turn spindles, which is going to be a limited market.

I appreciate the input of the guy on AAW who said it's worth $1500, but then again, it's always a different matter if it's your actual money that's being spent.

Re: So what's it worth?

#8

Re: So what's it worth?

Ken

>I would say,that unless you have to move it or need the money,I would set on it for a while and maybe the economy will pick up or the right person will here of it and take it off your hands.

Ken

Re: So what's it worth?

#9

Re: So what's it worth?

Stephen Mushinski

>Gary,

When I read the ad, I said to myself that is a great deal! Should you still have it in April when I am down your way I will jump all over it. Now that is all dependant on weather or not I have a job and can afford to spend my vacation at Arrowmont next year. If you are traveling up to Toronto area bring it with you I am sure I could hide it from Sharon somewhere! :)

Re: So what's it worth?

#10

Thanks all, and another question.

Gary Evans Tallassee, TN

>I do appreciate the input from everyone.

I thought perhaps I was a little too high on the price given the fact that I've had no response from so many views. I know the transport is an issue, but I'm willing to haul it a pretty good distance for little more than the cost of fuel. Ask Mike Fitterling about that. I also know that the short bed reduces the size of the market, but it is still a high end lathe for its intended purpose, even if it is no longer manufactured.

I do need to take some current pictures. The lathe is in a different building now and the VFD is mounted on a separate stand. Before I do that, I need to take another stab at removing dried finishes on the bed from the original owner. I went over it when I first got it a few years ago with alcohol, mineral spirits and lacquer thinner, but there is still some residual finish evident. Anyone know a good way to clean it up spic and span without removing the original paint?

Interestingly enough, buying the cleaning supplies for this lathe is when I found out the restrictions at Walmart on buying solvents. I didn't know that you can only buy one type of solvent at a time from them. I had to make three separate trips from car to store to get all the ones I needed. I guess I'm lucky nobody noticed and they didn't sic the drug taskforce folks on me.

Anyway, I guess I will continue my effort to sell. I don't really want to, but the money would help out at the moment. Plus, I just can't seem to focus on turning like I once did. This is the only place I've posted it thus far. Wouldn't hurt to spread the word around a little farther.

John K., if you are actually interested in the lathe, I'll send you an email with the answers to your questions. Do you still need some hourly help at your place?

Steve, I'd be happy to get together when you come down in April, whether I still have the lathe or not. I enjoyed our visit the last time.

Thanks again to everyone who posted.

Gary

Re: So what's it worth?

#11

Re: So what's it worth?

Michael Wilkins

>I have the same Woodfast short bed lathe with the variable feed drive. Got it from a local tool new/used tool retailer here in eastern NC. From my nickels' worth of opinion, I believe the lathe is priced correctly, especially considering what it cost new. I believe the Craft Supplies catalog that had this lathe in it (from several years ago) listed it in the $4500 range. Maybe higher.

The slow response could just be a sign of the times, and the fact that this is a short bed lathe. That is why I have my eyes open for a long bed lathe for longer spindles, while still keeping the shorty Woodfast. Enjoy your turkey.

Re: So what's it worth?

#12

Re: So what's it worth?

Steven Kubien

>Gary, I've been thinking of getting a bigger lathe for a while now and while I am intrigued by yours, I just can't justify it right now. The price seems more than fair to me.

One question (for anyone who knows)... Is there an outboard tool rest available for these things? I assume that something like the Vicmarc rig would work. I only ask because when I get few other things paid off, I may well look at a unit such as this when available.

Thanks,

Steve Kubien

Re: So what's it worth?

#13

Don't tell me....

Steven Kubien

>...that Sharon has the courage to venture near your shop? she's braver than I was previously led to believe. :)

Steve Kubien

Re: So what's it worth?

#14

Steven Antonucci

poor man's outboard rest

steve antonucci

>My headstock rotates, and the legs are drilled for a "factory unit" I don't turn enough "big stuff" to justify the cost, so I hacked this together out of plumbing fittings and some scrap 2x.

Because it sits on the lathe bango, it's pretty darned stable. If you have mounting holes on the legs of your lathe, no reason you can't do something similar.

Steve


img

Re: So what's it worth?

#15

Battery backup for lathe? :-)

GalenV

>

Re: So what's it worth?

#16

Dick Hines

Re: So what's it worth?

Dick Hines

>Gary it sounds like a good deal to me. The trouble is I don't have the room. I will check around my club to see if anyone wants a lathe.

Hope your holidays are good.

Re: So what's it worth?

#17

Re: poor man's outboard rest

john lucas

>Steve When I had my Nova 3000 I had to turn a table top. I didn't have an outboard tool rest so I clamped a pipe to my drill press table and pushed the drill press over to the lathe. It wasn't the most convenient thing but it worked.

Re: So what's it worth?

#18

Steven Antonucci

Trolling motor battery

steve antonucci

>Got to put it somewhere. Heavy as he11...

S

Re: So what's it worth?

#19

About your outboard rig, Steve

Steven Kubien

>Steve, I've seen pic's off your outboard rig before, but never really clear ones. Is the tool rest itself just 1" pipe, threaded on the end to accept an elbow to drop into the banjo? I would have thought the pipe would vibrate like, well, err, something that vibrates alot! What about the other end? Does it just fit into a 1" hole, or something more elaborate? I've got a hunk of cherry that is begging to be spun bigger than our 16" inboard will allow.

Re: So what's it worth?

#20

Steven Antonucci

What I did

steve antonucci

>1" black pipe to start is marginally too thick to fit the banjo, so I put it in my chuck and held a file against it until it fit. The toolrest is a big T, and I think the long piece was 3'. I put a short one on the other side of the T fitting, but have never used it.

I turned 3 small wooden plugs and epoxied one into the bottom and one end. Then, to dampen vibration, I filled it with sand. Worked like a charm. Other plug holds in the mess.

The pipe would be stiff enough as is, but I decided to support the other edge to overcome the canitlever. Also works great, and can be moved in or out depending upon the size of the object being turned. The shorter the section between the banjo and the upright, the stiffer the pipe feels. Even at full extension, it's more than acceptable for platters. If you have a big gouge hanging a long way over the pipe... still works, but not as solid as I'd like. I hollowed a 23" x 7" white oak bowl with it.

I could certainly execute the idea much better and prettier, but have never felt the need to. Close-up of the banjo attached...


img

Re: So what's it worth?

#21

Guess I've got...

Steven Kubien

>...a new project once I finish all of these pens I am working on, and Secret Santa, and Christmas gifts, work for the gallery........ Sleep would be nice some day.

Thanks for your help.

Steve

Re: So what's it worth?

#22

Re: poor man's outboard rest

Allen Neighbors

>Steve I've told a lot of people about your "poor-man's rest". I'm glad you posted this better shot of the toolrest/banjo connection.

I think it's a gem! I used it when I had my old Griz with the rotating headstock.

Re: So what's it worth?

#23

Re: poor man's outboard rest

Terry Scott

>I would recommend that any outboard attachement be attached to the lathe or the floor .We had an instance in our club were a member was using a outboard attachment and it walked towards the lathe because of the downward pressure on the tool rest he nearly lost his arm and ended up in a bad way .

On my lathe I have attached a solid tube that is held onto the lathe and stand by the way of a collect and grub screw .If you would like to see a picture email and Ill send yo one

Cheers

Re: So what's it worth?

#24

Pictures are good

Steven Kubien

>Ya Terry, I would love to see some pics (as I am sure others would). Perhaps start a new "outboard turning rig" thread?

Steve Kubien