Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Finishing with Brushing Lacquer

Posts

Finishing with Brushing Lacquer

#1

Finishing with Brushing Lacquer

Tom Henderson, Gulf Breeze, FL.

>I am looking for some advice on using this type of finish. I haven't had much success so far with brushing, padding, even when I thinned the lacquer way down. Runs, streaks, inconsistent coverage, you name it, I got it. Should I give up and get some spray cans?

Re: Finishing with Brushing Lacquer

#2

Re: Finishing with Brushing Lacquer

Greg Haugen

>What are you trying to finish? Large or small items?

I've used a thinned brushing lacquer as a "sealing" coat and then either applied a paste wax over it or repeated the process to slightly build up the finish. I've gone this on boxes and small items mostly. It's a Ray Key technique. With the lathe stopped, I dip a cloth in the thinned lacquer and wipe it on the piece. I give it 30 seconds to a minute to soak in. I wipe off the "standing" excess first, and then turn the lathe on to rub in/burnish the finish. The heat basically speeds the curing process. I've done on the inside of boxes and no "smell" was detected within an hour or so. It's a production method of sealing and finishing a piece. I also use it on ornaments, more of a sealing coat and then they're sprayed once assembled. Since the wood is sealed, the parts can be handled during assmebly without the fear of transferring fingerprints onto the bare wood plus it shortens the finishing time since it's sealed already.

As far as it being used as a finish that is padded, brushed? It's rather difficult to do so on a round vertical object. That technqiue would be best used for flat work, shelving, cabinets, etc. It can be used as I described as a sealer/primer coat, and I have built it up by repeating the thinned lacquer process and wiping it off then burnishing it.

Hope that helps,

Greg H.

Re: Finishing with Brushing Lacquer

#3

spray cans..deft

robert davis

>

Re: Finishing with Brushing Lacquer

#4

Re: Finishing with Brushing Lacquer

Texian

>Tom,

Have been using brush-on when I want to build a smooth, level, glassy finish. First, one or two coats of wipe-on lacquer base sealer. Then two or three coats of brush-on lacquer to build and seal the finish. Let dry a couple days and then sand smooth and level. Then a couple spray coats and buff lightly. The brush-on saves lots of $$ over trying to build a finish with rattle can spray.

Re: Finishing with Brushing Lacquer

#5

Re: Finishing with Brushing Lacquer

nick

>Look back one page for Russ Fairfield's post "Lacquer Link". He has some good advice. I have not had success with spray cans. I brush on several coats to get a good build, then level with P320 sandpaper. Then up through the grits until I get the level of shine I want. It's tedious but the only alternative is spray equipment, as far as I know.

Re: Finishing with Brushing Lacquer

#6

Re: Finishing with Brushing Lacquer *LINK*

Russ Fairfield

>Read the link.


http://www.woodturnerruss.com/FSOriginal11-Lacquer-1.html

Re: Finishing with Brushing Lacquer

#7

Re: Read this one too *LINK*

Russ Fairfield

>This explains a brushing application of a brushing lacquer with Deft. There are now brushing lacquers by Watco and Minwax. The directions are the same.


http://www.woodturnerruss.com/FSOriginal5.html

Re: Finishing with Brushing Lacquer

#8

Re: Finishing with Brushing Lacquer

Paul Zerjay

>Is pre-cat considered brushing lacquer? I use mohawk pre-cat lacquer (thinned) in an airbrush and have been having good luck with it. Sprayed while still on the lathe and spinning at 120 rpm's. Not much of an overspray issue with an airbrush.

Re: Finishing with Brushing Lacquer

#9

Re: Finishing with Brushing Lacquer

Darryl

>Tom before you give up buy a small srpay gun called "The Critter" about $39.00 on Amazon. with a compressor that will put out at least 50PSI you can get a very smooth and lasting finish with lacquer. The so called brushing lacquer can be sprayed right out of the can. The VOC's cause it to be labeled brushing but it really isn't much different. The Critter does not have an adjustable spray tip but since the medium is held in a pint mason jar it is easy to use and works well.