Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

First time hollow-form turning - - where next?

Posts

First time hollow-form turning - - where next?

#1

First time hollow-form turning - - where next?

Pete LaBelle

>Afteroon gents & ladies -

Have been turning bowls & such for a few years, and this past summer, was given a Sorby goose-neck hollow turning tool. Have been playing with it in green wood and having fun. Not knowing exactly where the tool is on horizontal center and also depth into the wood sure makes the work challenging.

Getting further into the hollow-form turning, where do I go from here? Am pondering one of the boring systems, possibly the Jamieson. Poor father of kids in college, will probably work on building one.

Do you hollow turners use such a jig? Anybody ever build their own? Is the other elbow joing jig better/worse ? Should I stick with hand tools for boring instead?

I have a Jet 1642 lathe.

Thanx for your wisdom !

Pete

Re: First time hollow-form turning - - where next?

#2

Re: First time hollow-form turning - - where next?

Don at Central Illinois

>There are a lot of 'systems' out there and most, if not all, work well to one degree or another. I don't have any, yet, I prefer to use hand held tools. One day I'll spring for a hollowing system with the laser, but can't afford suggest luxuries now. Good luck and I'm sure you'll get a lot of responses, pro and con to your question.

Re: First time hollow-form turning - - where next?

#3

Re: First time hollow-form turning - - where next?

Norm Smith

>Hi Pete,

I have lots of hollowing tools, home made and purchased. My tool of choice is the Don Pencil Scorpion system unless I am into larger pieces where I use a captive system.

Have fun,

Norm

Re: First time hollow-form turning - - where next?

#4

Re: First time hollow-form turning - - where next?

Cyril Griesbach

>Pete, I would believe that most hollowing is done with hand held tools and those tools are probably mostly hand made rather than purchased. But then, as I've often learned, I could be wrong. Many of the hollowing tools sold are available unhandled and that's the way I'd buy them because lots of the handles don't work well and most of the aftermarket handles will work with a variety of tools of the same diameter. In fact, most of the aftermarket handles are bored with one size on one end and another on the other end thus increasing their usefulness. I have some from Oneway, Peebles and Yoder with the last two being my favorite.

Now, I have a captured system as well and mostly because of my carpal tunnel and arthritis but I also do small and quick things by hand too with purchased and home made tools.

Hmmm...that seems clear as mud.

Re: First time hollow-form turning - - where next?

#5

Re: First time hollow-form turning - - where next?

Allen Neighbors

>I made my own rig. The main thing is a 5"x24" rectangle "anti-torque" gizmo made from 1" square tubing. One long leg has three 5/16 nuts braized on it for the set screws to hold the tool shafts. I have inserts for the smaller shafts but it holds a 3/4" shaft without inserts.

To the rectangle, I attached a 1/2" floor flange with a 10" riser pipe, that has a Tee on top. The Tee is threaded through the top for a 5/16 set screw to hold a sliding 3/8pipe which holds the laser.

The rig that holds the rectangle is made from a piece of aluminum across the ways, with 5/8 allthread risers to hold two lengths of 1" square tubing, separated by 1", through which, the rectangle slides. Total cost for this rig was about $20 bucks for the welding, some "slick tape" for the slide, nuts and set screws. I picked up the square tubing at the land fill metal pile. Cut the straight pieces out of it.


img

Re: First time hollow-form turning - - where next?

#6

Laser Mount 

Allen Neighbors

>


img

Re: First time hollow-form turning - - where next?

#7

Re: First time hollow-form turning - - where next?

Greg Haugen

>Pete,

I prefer "hand held" hollowing. It's the way I started and just haven't changed. I like the feel and control it offers. I can gauge thickness by the sound of the wood as it turns as well as by calipers. By going from thinner to thicker areas in the vessel I can hear the difference and know where I am. The more familiar you get with a tool-you'll know where you are in the form. A good set of calipers, I like the two different sizes "figure 8" double ended calipers from Craft Supplies but then the Sorby versions. Mostly due to the fact they're half the price and have a threaded knob so the "stiffness" of them can be adjusted. It can't be on the Sorby's. Since you're enjoying "hollowing" I'd recommend talking to a few local turners and get a chance to try their tools/systems. I've recently gotten a set of 5/8" thick kelton hollowers with the Ultimate handle. I must say I love them. The handle is also very nice since it has a collet, it's "tool-less" tool removal-no allen wrenches needed to change tools.

If you're looking for a captured system-I'd look at the Jamieson. Lyle has info on his site on how to build some of the parts. If you're looking at getting a set of hollowing tools-do your research and talk to other turners to see what they use. The most tool for your dollar? Either Trent Bosch's sets or Kelton Hollowers. Beyond that the sky is the limit.

Hope that helps.

Greg H.

Re: First time hollow-form turning - - where next?

#8

Re: First time hollow-form turning - - where next?

Pete LaBelle

>Thanx guys -

Will start collecting iron to build my own Jamison system. Went to Lyle's site and learned a couple more things that need to be incorported into the designs too.

Found the steady rest in the background of one of the photos interesting also.

Keep you posted on my results.

Pete

Re: First time hollow-form turning - - where next?

#9

Lyle Jamieson

Re: First time hollow-form turning - - where next?

Lyle Jamieson

>Hi All, I might make your home built system easier. I can sell you some of the machined parts individually to incorperate into your welded or bolted parts. Let me know if I can be of assistance. Lyle