Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

some stuff I've been turning

Posts

some stuff I've been turning

#1

some stuff I've been turning

Brian Simmons, Heflin, AL

>I have been making spherical boxes out of flat sawn wood glued up into a cube and the turned round. Makes a box that is a sphere with the hole inside is square. Anyway a few of the glue joints weren't as good as I would like and so I tried turning the cube between the corners to see what it would look like. I ended up with a neat ornament shape.

I recently made me some plywood using a mix of maple, black walnut, oak and african mahogany veneers and decided to use some of it to make one of the ornaments. This is basically a Christmas ornament permanently mounted on a stand. I cut steps in to show the character of the plywood.


img

Re: some stuff I've been turning

#2

Re: some stuff I've been turning

Brian Simmons, Heflin, AL

>a close up view


img

Re: some stuff I've been turning

#3

Re: some stuff I've been turning

Brian Simmons, Heflin, AL

>One of the boxes had an ill fitting lid so I turned it into a flower. Looks a lot like a tulip. These flowers were cut from some more of my homemade ply. The thorns are where I left rings on the turned shaft and the carved away all that was not a thorn.


img

Re: some stuff I've been turning

#4

Re: some stuff I've been turning 

Brian Simmons, Heflin, AL

>


img

Re: some stuff I've been turning

#5

Re: some stuff I've been turning

GalenV

>Really a unique group.

Are the flowers still square if you look into them if they started out as a box?

One looks like you lapped the box corners and others mitered?

This site amazes me on the different turnings that are being produced.

Something new for me to see every day.

Original!

Re: some stuff I've been turning

#6

Re: some stuff I've been turning

Brian Simmons, Heflin, AL

>They are square. Here is an end view of some I have yet to turn.

I create the mitered pieces and measure to decide the square that I cut to fit for the stem so that it is a tight fit.


img

Re: some stuff I've been turning

#7

Re: some stuff I've been turning

Brian Simmons, Heflin, AL

>starts life as a hollow cube (end removed for visual reference)


img

Re: some stuff I've been turning

#8

Re: some stuff I've been turning

Brian Simmons, Heflin, AL

>after chucking the fully enclosed cube between the corners and turning one half


img

Re: some stuff I've been turning

#9

Re: some stuff I've been turning

Brian Simmons, Heflin, AL

>after turning the second half, next step is to drill the ends and make the blanks that will make up the finial. Glue these finial blanks in and


img

Re: some stuff I've been turning

#10

Re: some stuff I've been turning

Brian Simmons, Heflin, AL

>turn between centers to blend in finial glue joints, final sand and use a razor to clean up triangles


img

Re: some stuff I've been turning

#11

Re: some stuff I've been turning

Brian Simmons, Heflin, AL

>a finished ornament. note the black walnut 'bowl'


img

Re: some stuff I've been turning

#12

Re: some stuff I've been turning

Brian Simmons, Heflin, AL

>this is a picture of a covered square hollow sphere. The one on the right had a lid that just did not fit close enough so I turned it into a tulip. The 45 degree chamfers cause the scallop shape on the sides. This tulip also started life as a hollow cube with one side removed.


img

Re: some stuff I've been turning

#13

Thanks for posting the before shot.

GalenV

>If you start by making your own plywood and then get to this point maybe turning is the easiest? Well carving the thorns may be troublesome if you prick your finger. Those thorns can be painfull.

Neat idea. Always find something new being done here.

Re: some stuff I've been turning

#14

Lidded "box" without outside corners! Neat! :-)

GalenV

>

Re: some stuff I've been turning

#15

Re: some stuff I've been turning

Don Orr

>Very cool Brian-way to think ouside the "box". This could evolve into some interesting combinations. Keep us posted.

Re: some stuff I've been turning

#16

Re: some stuff I've been turning

matthew fallon

>i really loved it, all of it'

thank you for sharing!