Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Thompson gouge for back hollowing?

Posts

Thompson gouge for back hollowing?

#1

Thompson gouge for back hollowing?

nick

>Has anyone used Doug Thompson's gouges for back hollowing? If so, which size/profile do you like best? I have a 3/8 in. spindle gouge that I like a lot but it is very flexible and vibrates too much with several inches over the tool rest. I asked Doug but he wasn't sure. Is the shallow detail gouge stiffer?

Re: Thompson gouge for back hollowing?

#2

Re: Thompson gouge for back hollowing?

john lucas

>The shallow detail gouges are much thicker. It is my reach for tool when I have to hang the tool over the tool rest. If you can imagine taking a 3/8" bowl gouge and filling in most of the flute you will get some idea of how thick this is. The spindle gouges have about half the flute thickness.

For the cut you are talking about I use either the Thompson V shaped bowl gouge or the 3/8" detail gouge.

Re: Thompson gouge for back hollowing?

#3

Re: Thompson gouge for back hollowing?

Fog Tanner

>I use Doug's 1/2" shallow gouge these days. It is ground with a normal fingernail grind with a thirty degree bevel. I have had several workshops with Raffan, and the 1/2" is what he uses. I have tried a 3/8" in the past but ran into too much flex and vibration. If I use the 3/8" I use it as Ray Key does. It is not as fast but better suited when I am using my Escoulen chucks.

Fog

Re: Thompson gouge for back hollowing?

#4

Re: Thompson gouge for back hollowing?

nick

>Thanks. I just ordered a 1/2" shallow gouge. How does Ray Key use the smaller one?

Re: Thompson gouge for back hollowing?

#5

Re: Thompson gouge for back hollowing?

Fog Tanner

>It is hard to describe the grind, it is not symetrical at all. The left hand side of the gouge is ground in what would be a normal fingernail profile, except it is around a 60 degree bevel instead of 40. From the center, the right hand wing is group back an inch or more such that it gives clearence when cutting, there is no way for it to contact the wood. Looking from above, it is a shallow curve along the right side from the center of the tip and the left looks normal. The way it is ground allows you to use the right hand side as a shear scraper on the outside. Craft Supply used to have a picture of it in their catalog.

To use it, you position the tool on center. If you put a ruler accross the flute it would be pointing about 5 degrees past vertical towards 1:00. You can then push the gouge in much like a spade pit and drill your depth hole. I put a mark on the gouge for the target depth.

Once you have the hole "drilled", you start with the gouge at center and the flute at a 45 degree angle (around 10:00). Using your left hand as a pivot point you move the edge through an arc from center towards the edge. The depth of the cut is dictated by the shaprness of the tool, wood, how much out of the chuck/over the rest and how much of a hurry you are in. You will be "told" when you are taking too much. You repeat until you get to the bottom of your depth hole and then clean up with a scraper.

After posting earlier, I wound up with a piece of wood in on of my Vicmarc/Escoulen chuck and decided to hollow it using my 3/8" Key gouge. Worked as described above, the piece didn't give a hint of coming out of the cup chuck. It produces much less lateral load than when using the backhollowing technique - at least in my case. I tend to get in a hurry when back hollowing since the wood comes out so quickly. It is worth learning the Ray Key method for those times where you need a more delicate hollowing method.

I think you will like the Thompson gouge for back hollowing. The flute depth works better than my Henry Taylor that had always been my goto gouge for that.

Fog

Re: Thompson gouge for back hollowing?

#6

Re: Thompson gouge for back hollowing?

Allen Neighbors

>Every time I decide I want to try to back hollow, I forget how. Then when I'm inside at the computer I forget to search for the way it's done. I guess that's another sign I'm gettin' old. :)