Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Stupid question about sand paper

Posts

Stupid question about sand paper

#1

Stupid question about sand paper

Ray Carson - Lawrenceville, NJ

>Okay, there's "sand paper" and then there's "sand paper". There's flint, (not found commonly) garnet, emery, aluminium oxide, silicon carbide, alumina-zirconia, chromium oxide, etc.

I here of the turners here at WC "sanding through" 400, 600, 800, and even higher grits to achieve the ultimate smooth finish. And the turned pieces ARE beautiful.

I can find sand paper at the big orange and big blue box stores. I even buy it at my local hardware store on occasion and I usually use garnet paper for most cabinet work sanding up to 220. The problem is I can't find garnet paper in 400, 600 and 800 grits. So what are all of you using?

Question:

What type of sanding media do you use for turning (most of the time) and where do you find grits in the 400, 600, 800 range? Is this the charcoal looking stuff used for metal working? Does the black grit get embedded in your turnings and effect finishes? Where do you buy the grits posted here at WC?

Okay that was more than one stupid question. :-)

Thanks in advance,

Ray

Re: Stupid question about sand paper

#2

Dick Hines

Re: Stupid question about sand paper

Dick Hines

>I don't think fro bowls you need to go down pass 400. The big Orange box store sells Norton 3X Insheet from the 3X is all I use..

Re: Stupid question about sand paper

#3

Ric Taylor

Re: Stupid question about sand paper

Ric Taylor

>Ray,

I buy sheets of Norton in a variety of grits including 320, 400 (and I think) 600 at Home Depot. They come boxed with about 12 or 15 sheets per box (I'm not at home right now, I'm just remembering off the top of my head). The higher grits (800 through 2000) I get at other hardware stores, like Ace Hardware.

I get all of my sanding disks through the catalogs and websites from the various popular woodturning supply companies.

Ric

Re: Stupid question about sand paper

#4

Re: Ric's response

Ray Carson - Lawrenceville, NJ

>Are the 320 and higher grits you find at HD, aluminum oxide or silicon carbide? Can you use silicon carbide on wood without effecting the finishes?

Ray

Re: Stupid question about sand paper

#5

Re: Klingspor Bargin Box

Steve in NC

>I am fortunate to work just a few minutes from a Klingspor Woodworkers Store. THey have a large bin in the back with off cuts of several grits. I prefer the gold but use what they have. You buy it by the pound. It is all cloth backed. Another alternative is to buy the Klingspor bargin box via mail order. Just be sure to get the fine to medium box.

Steve

Re: Stupid question about sand paper

#6

JL

Email Norton. *LINK*

JL

>You can also request literature on any of their products via their website.


Norton

Re: Stupid question about sand paper

#7

Re: Klingspor Bargin Box

Michael Stafford

>Like Steve, I have access to a Klingspor store and buy grocery bags of Klingspor gold at $3 per pound. I do not have to frugal with sand paper....It may not be the best but it is hard to beat at that price.

Re: Stupid question about sand paper

#8

Ric Taylor

Re: Ric's response

Ric Taylor

>Ray,

I don't know what it's made of, I don't get lost in all of the technical details. I just know that Norton is considered by many to be the best brand for woodworking, and it works great for me.

I try to stay away from the black sandpapers on light wood, because they can leave residue in the pores of the wood, and discolor the wood with a grey tint.

Other than these points, I just try to keep it simple. Norton when possible, and no black on light wood.

Ric

Re: Stupid question about sand paper

#9

Re: Stupid question about sand paper

John K Jordan

>I like the Klingspor Gold in 2" and 1" rolls to P400, bought by phone from Klingspor. I mount them above the lathe as in the picture below.

For finer grits my new favorite is the Rhinowet paper, cut into little strips.

JKJ


img

Re: Stupid question about sand paper

#10

Re: Email Norton - I saw LINK

Ray Carson - Lawrenceville, NJ

>Thanks JL. I just finished viewing some of extensive info. at Norton and it looks like the 3X stuff is the way I want to go. I can't find the higher grits though at my Home Depot. They go up to 220. Believe me, I've looked. Stupid orange store. :-)

I'll keep digging. The other posts on my thread are recommending Klingspor so I'll have to check them out.

Thanks,

Ray

Re: Stupid question about sand paper

#11

Re:John K's PIC - nice sandpaper rack

Ray Carson - Lawrenceville, NJ

>Whoowee John !!!, that's some setup you got there. I think you got it covered. It sounds as though silicon carbide is off limits and not used a whole lot, 3X by Norton is one option and the rest of you like Klingspor. I like the accessibility of your sandpaper rack. It's all right there.

I'm a few months (years) from being that organized with my lathe / turning setup. Heck, I just finished a bowl and I'm reluctant to post it on WC for fear of the scrutiny. LOL You guys (and gals) here on the round side of WC are amazing. I haven't seen a turning here I didn't love.

Anyway, I appreciate the picture. It shows me that there's more to this than I'm looking at.

Thanks,

Ray

Re: Stupid question about sand paper

#12

jim miles

Re: Stupid question about sand paper

Jim Miles

>From about 600 grit and up is not commonly used in much woodworking - so you don't find much of it at woodworking sources. It is commonly used in auto body refinishing - so if you are looking for it go to the local auto parts store.

Re: Stupid question about sand paper

#13

Re: Stupid question about sand paper *LINK*

john lucas

>Ray I use the Norton 3x up to 400. From there up I use the finishing paper from Bruce Hoover at the sanding glove.

On my mini lathe I use rolls of Klingspor gold 1" and 2" wide. I have them on a dowel support system kind of like John K Jordan. I tear off what I need. You can get these up to 600 grit. Because of the thicker finishes that I use I seldom go beyond 400 because I simply can't see the difference.


http://www.thesandingglove.com/

Re: Stupid question about sand paper

#14

Re: Stupid question about sand paper

nick

>I think the point here is that turned wood needs to be sanded (if sanded at all) to 220 to 400 grit, depending on the wood. In cabinet work 220 is adequate because it is parallel to the grain. But sanding on the lathe is cross grain so usually needs to be finer. The higher grits, 600-200, are for sanding the finish. I know some turners use these very fine grits on the wood but that seems a waste of time if you are using a film finish. Then the higher grits determine whether you end up with a finish that is matte, satin, semi-gloss, etc.

BTW, the finest grits are also available at automotive supply stores as are the rubbing compounds needed for a high-gloss finish. Hope this helps.

Re: Stupid question about sand paper

#15

Re: Sandpaper responses

Ray Carson - Lawrenceville, NJ

>Thanks everyone for your input on my STUPID questions. I realize now that there was a little more to this than I originally thought. I learned a few things over the past day or so.

Oh yeah.....I'll never ask a STUPID question again. :-) LOL

Thanks,

Ray