Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

collets and collet chucks

Posts

collets and collet chucks

#1

collets and collet chucks

keith zimmerman, Normal IL

>Has anyone used the spindle collets that use a drawbar to tighten the jaws? I just picked up a set after trying to use a Beall collet chuck and almost breaking my hand while trying to tighten it.

thanks in advance.

keithz

Re: collets and collet chucks

#2

Re: collets and collet chucks

john lucas

>Keith I have a set of #2 morse taper collets that I bought from Enco. They work fine but the piece that goes into them has to be pretty close to exactly what the collet says. There isn't much leeway. I also had a problem with one old one that had a step in the taper. It wanted to lock up and not release so I tossed it out.

I haven't tried the Beal collets yet so I can't compare. You do have to apply a fair amount of pressure to the #2 collets to get them to lock solidly. I then use a mallet to get them to release so you need to make your tightening handle solid enough to take a blow from the mallet or make your threaded rod long enough to tap on it to release the collet.

Re: collets and collet chucks

#3

Re: collets and collet chucks

Don Evans

>Keith:

It sounds to me that you were trying to hold something that was too small for the particular collet.

I'm referring to machine collets and they come in sizes like 3/8 and 1/4 which are the two I have and they mean they hold something 3/8's and 1/4 nothing else. The collet are precision made and over tightening would be very likely also, so experiement to learn just how much you have to tighten. I'll bet it's much less than you think in order to secure it safely.

If you had to tighten it as you describe I think whatever it was was too small or it was wood that compressed too much.

As far as removing them, I make my own drawbar out of threaded rod and a round handle and washer on the out board side. The trick is to make the rod just 1/2" longer (protruding) and no more. This way when you turn the handle out to the end of the rod you can use it to tap on to loosen the collet. I like the soft touch round handles for this. The collets and handle came from:

www.mscdirect.com

Don

Re: collets and collet chucks

#4

Re: collets and collet chucks

keith zimmerman, Normal IL

>Don, the problem I had was with the Beall collet chuck using a 1/4" collet. The piece being mounted was exactly 1/4" as I measured it with a 1/4" open end wrench (and we all know that those are exactingly accurate ;-)). The problem I had was with the spanner wrench. they are so cheap that they don't fit very well and slip very easily. I smacked my hand on the lathe ways when the d**n wrench slipped while I was tightening it. I am switching to the style of collet that fits in the spindle and uses a drawbar.

I have to make my own drawbar, so the info you shared about making one will help me a lot. Thanks

keithz

Re: collets and collet chucks

#5

Re: collets and collet chucks

Danny Wells

>Keith,

All collets have a very small tolerance for the sizes that they will hold. I recently purchased the Beall system and also have the system from Woodcraft that fits into the morse taper. Both systems only have about 1/32 or less tolerance for what they will hold.

So I don't think changing your system will solve your problem. I would suggest you try turning your tenon to a more precisely measured size before spending the extra bucks.

I haven't had any problems with either system by hand tightening, if the tenon is properly sized, but if its too small, you can't tighten enough to hold even with the spanner.