Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Has anybody...

Posts

Has anybody...

#1

Has anybody...

GaryG in MD

>...put Watco Danish Oil over wood that has been dyed with RIT water-based fabric dye and sanded partly back to highlight curl?

I have an experiment started on scrap, but I would like to hear experiences, good or bad, that any of you may have had.

Does the oil soak through or mostly sit on top and cause problems?

Does it darken the color?

Is it better not to do it for any reason?

Will the oil still pop the grain (and curl) of the underlying wood?

(That's my reason for wanting to do it.)

Is it better to just go with something like MWOP or clear acrylic over the top instead? It doesn't pop the grain, but the latter is supposedly a UV protectant and might stop the dye from fading so quickly.

All thoughts welcome, Gary

Re: Has anybody...

#2

Re: Has anybody...

john lucas

>Gary The dye is supposed to pop the grain. I was trying to go further by dying the grain a different color to really make it pop. This was on quilted maple. The only problem I had was that I sanded too much removing too much of the color in some areas. You have to sand very carefully to get just the smooth part back to natural and leaving the quilted part colored. At this stage the oil finish doesn't change it dramatically because you've already done that. I think if you used a really dilute dye to just change the look of the quilted part then the oil might help. In my case it was so dramatic that any finish would work. I used min wax wipe on poly.

Re: Has anybody...

#3

thanks John

GaryG in MD

>Yes, I understand what you're saying -- I'm on my fourth application of dye because the first three times, I cut it back too much! ;-) This is my first experience with dye, and I want it just right. Thanks for the info. (This is that same bowl I ripped the edge off of -- with luck, it's going to be a combination of a Jennifer form and a Cindy coloring.)

...Gary

Re: Has anybody...

#4

follow up...

GaryG in MD

>John, I don't want to darken this silver maple too much, but I do want to pop the curl, so I haven't decided yet if I'm going to use Watco Danish first or go straight to MWOP. The RIT color is only on a portion of the bowl (the top, surrounding a smaller lipped depression -- the bottom/sides will be natural). There are edges where the color and bare wood meet. It won't be easy to keep the finish off the RIT at those edges, so I'm guessing it would be easier/better to just put the finish, whichever it turns out to be, over the color as well. Is this going to be a problem if it's Watco? (As I say, I have the experiment going on scrap, but it never hurts to ask.) Thanks, Gary

Re: Has anybody...

#5

Re: follow up...

Don at Central Illinois

>Sounds interesting. Please post photos so I can see exactly what you are describing.

Re: Has anybody...

#6

will do...

GaryG in MD

>Don, I'll post it as soon as it's presentable and I get the photos off the camera and onto the computer. Thanks for your interest. ...Gary

Re: Has anybody...

#7

Ric Taylor

Re: follow up...

Ric Taylor

>Gary,

To keep the finish off the dyed area, use a masking material.

Here is what I would do, if I understand what you are saying. I would first seal the area that you don't want dyed with a 50/50 mix of lacquer and thinner. That will help keep the dye from bleeding into the area you don't want dyed, and it won't darken the wood. It will help to pop the grain.

After the dye has been applied, head to the grocery store and get some Glad Press and Seal. It is like Saran Wrap, but it is tacky on one side and it stretches to conform to any shape. It makes a great masking film, and it is lots cheaper than the masking film that is sold in art supply stores. It will cling to your turning nicely. Use it to mask off the dyed areas, then apply your finish to the rest of the piece.

Ric

Re: Has anybody...

#8

Re: follow up...

GaryG in MD

>Thanks Ric -- that's good info. I wasn't familiar with that product. I'll keep that in my bag of tricks.

In this particular case, I think I want to put a film over the RIT -- it's a little too flat, and my experiments show that something like a coat of MWOP or CAMS (clear matte acrylic spray) gives some beneficial sheen, and I'm going to use it as a UV protectant to try to keep the RIT from fading.

What I haven't experimented with is putting RIT over the partly sealed, partly popped surface. I'll try that next to see how it compares to putting the RIT onto raw, sanded wood.

...Gary