Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Laser tachometers

Posts

Laser tachometers

#1

Laser tachometers

wilbur

>I am getting an old Conover lathe tuned up. Currently it has a pulley speed change setup, with a four step pulley on the headstock, a four step pulley on a short jack shaft, and a two step pulley that couples the jack shaft to the motor, which gives a total of eight possible speeds. Problem is, I don't know what those speeds are.

Has anyone used a laser tachometer for determining RPMs? That's the easiest way I could think of for measuring the actual RPMs.

Re: Laser tachometers

#2

Re: Laser tachometers

Mike Brazeau

>Wilbur - I borrowed one from a fellow guild member and recorded the speeds for my Oneway 2436. I believe I posted it here. Very easy to use. Place a small piece of reflective tape on the shaft somewhere and point it and read. The one I used sells for about $35.

Re: Laser tachometers

#3

it's a simple math problem

john lucas

>I'm not the person to ask but I did look it up one time. You know the motor speed and the pulley sizes so it should be pretty simple to plug these in a formula and simply make a chart that can be pasted on somewhere.

Now I'm a gadget freak and I'm all for buying the tach, been wanting one myself, I don't know why but it just seems so cool.

Re: Laser tachometers

#4

Re: Laser tachometers *LINK*

Dave Peebles Lyons, Ohio!

>Hi Wilbur,

Here is a pdf that Michael Latcha posted a while back. It is the manual for the Conover lathe. It looks like there is some info about the speeds when using the jack shaft on page 10.

Best wishes,

Dave


Conover Manual

Re: Laser tachometers

#5

Thanks Dave!

wilbur

>Oh, that is so excellent. That manual is just what I needed!

Re: Laser tachometers

#6

Steven Antonucci

Kinda dumb question: why does it matter?

steve antonucci

>I have 8 speeds on my Nova via a stepped pulley, but I don't know what they are (to an exact RPM!) I think of them as painfully slow to scary fast, and usually pick something in the middle. Whether it's 800 RPM or 818 RPM isn't something I can change, so I just think in terms of more and less...

Steve

Re: Laser tachometers

#7

Re: Laser tachometers

Fog Tanner

>I have never used a laser tach, but used mechanical and optical tachs quite a bit. The optical tach have was made for reading rpm off a two bladed prop. Its biggest drawback indoors is you havd to use a flashlight as the light source. Indoor lighting will always give a reading of 3600 rpm regardless of the actual rpm. Hopefully the laser would not have the same issue. The mechanical tachs are a friction drive and will give you a reading on just about anything that spins. They typically have differnt drive adapters that allow you to adapt to different surfaces.

I have also used digital readout tachs, which I find harder to read than the analog type (i.e. dial). I am typically in a hurry and the digital numbers bouncing all over the place is a distraction, while the needle on the analog is more steady. The scale also gives you a reference point for what you are working against, something missing on the digital readout. My Vic has a digital readout and I just round to the nearst "50" when dealing with the three different pulley ratios. Would be a nice feature to have a button to set the readout for the different pulley ranges. But, I just use it to let me know if I am getting into an rpm that is dangerous for the bowl blank I am turning. Funny how I spent a week with Raffan and never once knew the rpm we were turning at, no readouts. Its only having the readout available that makes it a concern.

Re: Laser tachometers

#8

Re: Kinda dumb question: why does it matter?

wilbur

>Oh, I don't need the exact speeds. It's that I have no idea what the speeds are, with the way that my lathe is currently set up. On the headstock there's a little chart that puts the speeds at 600, 1100, 1725, and 2600 RPM, but that's assuming that the motor is directly driving the four step pulley. Because of the jack shaft, and the extra two pulleys, I know that the slowest speed is slower than 600 RPM, but that's about it.

Re: Laser tachometers

#9

Re: Kinda dumb question: why does it matter? *LINK*

Bob Entwisle in NJ

>Hi wilbur,

There are bunches of pully diameter motor speed calculators online.

If you know the motor speed and the pully diameters you should be able to develope a speed chart for your lathe.

I googled "pulley diameter speed calculations" and came up with the link below, but there were plenty of other choices.

Or you could just order up a laser-tach....

Bob


http://www.csgnetwork.com/pulleybeltcalc.html

Re: Laser tachometers

#10

Re: Laser tachometers

bill Crommett

>All of this reminds me of Lisi Oland at Unicoi many years ago when someone asked her what speed she was turning at the time. Her reply was something like:"I'm comfortable with it "

Re: Laser tachometers

#11

Re: Laser tachometers

Texian

>Wilbur,

Check my post on the other forum. You can read the motor speed from the nameplate. The other speeds are simply the ratios of the pulley diameters. If your motor speed is 1800 rpm (rounded off for this example) and it has a 2" pulley driving a 6" pulley on the jackshaft, then the ratio is 2/6 or 1/3, so the jackshaft speed is 600 rpm. Now if the jackshaft has a 2" pulley driving a 6" pulley on the lathe spindle, the ratio is again 1/3, and the spindle speed is 200 rpm. If the jackshaft pulley is 2" driving a 4" pulley on the spindle, then the ratio is 2/4 or 1/2, so the spindle speed is 300 rpm. Hope this helps. And what kind of wood is the bed made from?

Re: Laser tachometers

#12

Re: Laser tachometers

wilbur

>Got it, thanks.

The bed is glued up from long pieces of microlaminated plywood, and is 2" x 6", more or less.

Re: Laser tachometers

#13

Re: Laser tachometers

Jerry Cox

>I made a variable speed conversion to my JET mini..being a type A personality, I HAD to know the speeds...I got a laser tach on Ebay...cost under $40 including shipping...works great, easy to use..I posted the new speeds on my control box...I am very pleased..

Re: Laser tachometers

#14

Re: Laser tachometers

Peter Hyde

>Lot's of good info for you Wilbur. I would just like to add the laser tach is a good shop investment. It reads the actual speed at the end of the driveline and so it is real speed. Calculations are fine but don't allow for wear on the sheaves or fluctuation in voltages. So if you want an accurate reading the tach is the way to go. Mine was $27 from Princes Auto in Canada. Certainly not critical for turning wood but still nice to know exactly what your setup is doing IMHO.

Re: Laser tachometers

#15

Re: Laser tachometers

Fog Tanner

>I find the readout only helpful in keeping me out of trouble these days. I added a balancing system to my lathe and was roughing out a large bowl over the weekend. I decided to take the time and adjust the counter weights since it was so off balance. Once it was set, I dialed up the RPM to something that looked good with no vibation. I checked the readout and found I was a bit over (a few hundred) the "safe" or recommended speed for that size blank. So I dialed it down to the speed I would normally turn that size when finishing.

Re: Laser tachometers

#16

Re: Laser tachometers

Texian

>Thanks Wilbur. Should be very stable.

Re: Laser tachometers

#17

My pleasure Wilbur

Dave Peebles Lyons, Ohio!

>Awesome lathe you have there!!

Enjoy it,

See ya,

Dave