Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Balancing Grinding Wheels

Posts

Balancing Grinding Wheels

#1

Balancing Grinding Wheels

Jorge Castaneda ~ Downeast Maine

>I splurged on the blue Norton wheels from Hartville tools, then went whole hog and got the Oneway wheel balancer. I just spent the las couple hours trying to balance them and just could not. Both wheels have a definite "south pole" and even with the counterweights of the wheels balancer all the way up to the north pole, they do not balance it, the south pole is still heavier.

It makes me think that the wheels are bored out of center, I did not dismantle the balance r to corroborate this theory, it is just an inference.

Anybody has experience same, or can give pointers on how to achive balance?

Do I have to dress away some weight out of the south pole?

TIA

JOrge

Re: Balancing Grinding Wheels

#2

Re: Balancing Grinding Wheels

Allen Neighbors

>I had trouble with mine, too, Jorge. I finally added another little bolt for an extra weight. It worked. Takes a lot of hit and miss.

I wish you well, my friend.

Re: Balancing Grinding Wheels

#3

Re: Balancing Grinding Wheels

bill Crommett

>Al: where did you put the little bolt ?

Re: Balancing Grinding Wheels

#4

Re: Balancing Grinding Wheels

GalenV

>Forum on Oneway web site noted the same problem with Norton blue wheels and Allen's solution to add another screw for weight was used. Another person noted they just mounted and dressed the wheel round to new Oneway hubs and then balanced. If the density still throws it off then again Allen's method still applies.

I had problems with new Norton white wheels as the plastic step bushings were so out of round it wobbled, so lucky my old bushings were used and they ran true. Wish I had the balancer too! Short on cash.

Re: Balancing Grinding Wheels

#5

Mike Hunter

Re: Balancing Grinding Wheels

Mike Hunter

>Jorge, Allen ... Timing is good on this balance topic. I also have the blue Norton wheels and spend a couple of hours yesterday chasing this balance. Finally I took the wheels off and put them back in the box. On Monday, I am going to find out if there are other bushings to use as the old wheels are now re-installed and run true.

I called another turner in our club and his blue Norton wheels were installed and ran true right out of the box.

Re: Balancing Grinding Wheels

#6

Re: Balancing Grinding Wheels

john lucas

>I don't have a oneway balancer but have always been able to get my wheels in balance by marking the high spot and then shifting the wheel slightly by losening the nut. Sometimes I have to rotate it as well as trying to shift it. When I get it as close as I can I true the wheel with a diamond hone and it's done. It takes a while to do this but in only has to be done once for the life of the wheel.

Re: Balancing Grinding Wheels

#7

Thoughts on Balancing Grinding Wheels

Bill Tindall, E.TN

>If I understood your post correctly you used some balancing thing but did not true the wheel circumference? I don't ever see a balancing thing on grinders in metal shops, which is a good indication that it is unnecessary, at least for their operations.

I buy and use lots of wheels of the highest "tool room" quality. Never-the-less, it is normal to have to true the circumference for a particular wheel, bushing (if needed) and shaft. The plastic bushings are particularly problematic.

The oneway wheel dresser is a good tool for those not adept at truing free hand (which includes me). It is very easy to just replicate the out of roundedness with a stick wheel dresser.

There are a number of issues here. Modern consumer grinders don't weigh much, so they are more sensitive to unbalance. Wheels are sold with the assumption that they will be trued upon installation. The plastic bushings are not ideal for the task they are employed. The availability of balancer things leads l the new owners of these things to fret where fretting may not be necessary.

If the grinder isn't walking off the bench, get back to turning, or clamp it down and get back to turning.

Re: Balancing Grinding Wheels

#8

Re: Balancing Grinding Wheels

Allen Neighbors

>Right at the top, opposite the heavy side of the wheel.

Re: Balancing Grinding Wheels

#9

Re: Balancing Grinding Wheels

Allen Neighbors

>I understand, Mike. The reason I didn't try to exchange the wheels I bought, is that I live so far from the Woodcraft. 245 miles from me to the closest one.

BTW, I love that little cutter, Mike. It's my go-to tool for end grain hollowing on little boxes and ort bowls. And you're a gem, too, Sir.

Re: Balancing Grinding Wheels

#10

Re: I have found many of the .......

Jamie Donaldson

>... Woodcraft grinders made difficult to true due to both the plastic shaft inserts and stamped metal flanges which are not flat or symetrical. Loosening the nuts and hand rotating to a best balanced position is aided by marking a spot on both wheel and motor shaft for indexing, then tighten and true the wheels.

Re: Balancing Grinding Wheels

#11

Re: I have found many of the .......

ken Tampa an NC

>1st I know it a pain to return them and have to wait for new ones.I had the same problem,but am a little closer to woodcraft,so I took them back and had them check out two new wheels on there grinder before I left the store.They went thru 6 wheels before they found some good ones,but if you have to mail them back,tell them to do this and I think it will be worth the wait.

2nd I don't believe in balancing a grinding wheels,putting a bunch of weights is asking for trouble.Your just bal one side to the other,but you still have an out of bal wheel.If you can't true it uo with a dressing wheel,then replace it.Just my 2 cents

Ken

Re: Balancing Grinding Wheels

#12

Re: Balancing Grinding Wheels

Jorge Castaneda ~ Downeast Maine

>Allen, Mike,

I measured my wheels and they are perfectly round, but one side must be denser. I added a heavier washer to one of the weights in a wheel and that and some fine tuning did it.

In the other wheel, a heavier washer was too much, so I did put a miniature magnet that came out of a battery dispenser for my hearing aid and that just did it, and a drop of CA hoping it stays there.

The wheels are running very smooth now, no vibration at all and coast a long time after turning the grinder off. :-)

Thank you gentlemen

Jorge

Re: Balancing Grinding Wheels

#13

Re: Thoughts on Balancing Grinding Wheels

Jorge Castaneda ~ Downeast Maine

>Bill,

Last night I did not even tried to true them in case I decided to send them back, this morning I measured and they are perfectly round, see my post under Allen and Mike.

I agree with you, in the metal shops you never see a balancer, but most of the time the grinders are big and heavy, mounted in a heavy cast iron stand. I did own one years ago, with a Baldor motor, that motor ran very smooth even just sitting on top of the bench. The grinding in a metal shop is usually heavy grinding, in our turning shops we need a very slight touch and finesse, and that is not easy with a wobble or vibration in the light weight grinders we use, mine is a $58.00 Ryobi! but now is running like a champ. : )

Thanks

Jorge

Re: Balancing Grinding Wheels

#14

Thank you All

Jorge Castaneda ~ Downeast Maine

>The grinder is running great now and now I am back to turning. : )

Thanks again

Jorge

Re: Balancing Grinding Wheels

#15

Re: Balancing Grinding Wheels

Dennis Yoder

>I had simular problem a while ago and found that there were 2 areas of concern. The plastic sleeve was out of round, I turned a new one out of hardwood. 2nd the wheel was out of round also. I trued it up with Don Geiger's wheel truing fixture. When I was done I could take off the Oneway balancer and it ran balanced. Dennis Y

Re: Balancing Grinding Wheels

#16

Mike Hunter

Re: Balancing Grinding Wheels

Mike Hunter

>Thanks Allen ... will you be at SWAT?

Re: Balancing Grinding Wheels

#17

Re: Balancing Grinding Wheels

Allen Neighbors

>Depends on what the CFO decides. Right now I don't even know when it is.

Re: Balancing Grinding Wheels

#18

Re: Balancing Grinding Wheels

Allen Neighbors

>Glad you got it going right, Jorge.