Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Cylinder Jig...

Posts

Cylinder Jig...

#1

Cylinder Jig...

Rob Hix - King George, VA

>Hey all,

I am about to embark on a journey in which I will need to make a LOT of cylinders on the lathe. The cylinders do not have to be perfect, but the closer the better. Does anyone have any type of jig (other than a duplicator) that can be used to turn more perfect cylinders than just by hand.

Maybe I just need to practice more to get better at doing the cylinders by hand. Never hurts to ask though.

Thanks in advance,

Rob Hix

Re: Cylinder Jig...

#2

Re: Cylinder Jig...

mpax356

>If you start out with identical size blanks and practice your roughing technique with a spindle roughing gouge, I believe that you will be able to keep them in very close tolerances.

Re: Cylinder Jig...

#3

Re: Cylinder Jig...

John K Jordan

>I find if I set my long tool rest exactly parallel to the axis, I can turn a pretty close cylinder with the skew by sliding my forefinger along the rest. (The rest I use has no center obstruction - saw a oneway rest recently and I thought it was awful.)

JKJ

Re: Cylinder Jig...

#4

Re: Cylinder Jig...

Ken Grunke from SW WI

>Rob, for something like that I have used an angle-iron toolrest, set parallel with the lathe axis. Then a spindle gouge (the kind made of round shaft, like a bowl gouge) or a bowl gouge, with one hand riding along the toolrest as a depth guide.

I have also used my skewchigouge (fluteless gouge) with a setscrew collar on it. The collar rode along the angle-iron toolrest to set the cutting depth. It didn't give a very smooth surface, and was actually harder to control than just using my hand as a depth guage.

Seems like it was more trouble than it was worth, using a setscrew collar.

If you are fairly good with a skew, skip the first step and just use that. A planing cut can give a very straight, smooth surface.

Re: Cylinder Jig...

#5

Re: Cylinder Jig...

Rob Hix - King George, VA

>Thanks all,

I figured practice was the key. For several years now I have wanted to make chairs and stools. I am particularly lustful of being able to make a Shaker Rocker. I figured I would start off with some small post and rung stools and go from there. My first ones will probably be from borg 2x stock, so I can afford to make some mistakes.

Thanks again, now, off to practice on the lathe.

Rob Hix

Re: Cylinder Jig...

#6

Re: Cylinder Jig...

john lucas

>Many years ago a friend had to make duplicate parts for a porch. He rigged up a system of accurately making parting cuts to the same depth. He used a system mounted to the back of the lathe with bent wire that set on top of the wood. When the parting tool reached the proper depth the bent wire would drop through. Once he got all the bent wires to drop through all he had to do was connect the low point by first using a rough out gouge and then the skew.

With out the wire this is exactly how I do matching parts. I use calipers set to the proper final size and use the parting tool to cut to depth with the calipers held in position.

If you stated with a long tool rest set parallel to the bed you could clamp a stop to the parting tool to get all the depth setting right.

Re: Cylinder Jig...

#7

Steady Rest?

Al Kapocius

>If'n you're turning long slender spindles, check out steady rests to keep the center from flexing and wobbling. Might be faster to turn two or three spindles at a time.

Al Kapocius

Re: Cylinder Jig...

#8

Eyes, Skew &Calipers...

Jorge Castaneda ~ Downeast Maine

>