Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

BIG Turning *LINK*

Posts

BIG Turning *LINK*

#1

BIG Turning *LINK*

Don Orr

>This is the biggest thing I have ever or probably will ever turn on my lathe. It is the mainsail winch for the Onrust that is being built locally.My lathe is a Jet 1642 which supposedly is capable of handling a piece of wood 16" diameter and 42" long. However, you have to factor in the drive center, the revolving center in the tailstock and the height of the banjo. So I was limited to actual capacity of 12" diameter and 38" length. The piece of wood is guess what-12' diameter and 38" long! What I started with was a 12" x 12" x 54" piece of white oak. I knocked off the corners and cut it to length (hit only 1 nail). It took 2 of us to lift it onto the lathe. It took 2 hrs to rough down at VERY low rpms. The whole thing took 3 hrs to complete.The final piece turned out 36" long including the tennons and about 11 1/4" diameter. I'll have to post several photos separately since I don't have a webhost yet. It was a lot of fun. Two friends from my turning club came and helped. The people running the Onrust project also came to video and photograph it.


The Onrust Project

Re: BIG Turning *LINK*

#2

Sorry pic got "previewed" out

Don Orr

>Starting out.


img

Re: BIG Turning *LINK*

#3

Pic 2

Don Orr

>My friend Mike takning his "turn".


img

Re: BIG Turning *LINK*

#4

Pic 3

Don Orr

>My friend Dave turning. Dave is also a volunteer at the ship as am I.


img

Re: BIG Turning *LINK*

#5

Pic 4

Don Orr

>Left hand tennon which will ride in a block.


img

Re: BIG Turning *LINK*

#6

Pic 5

Don Orr

>Right hand tennon.


img

Re: BIG Turning *LINK*

#7

Pic 6

Don Orr

>Finally done. Nothing particularly difficult profile wise, just the size and weight (which I forgot to weigh). It's fairly straight except for a slight dip in the middle which will not effect the operation.


img

Re: BIG Turning *LINK*

#8

Re: BIG Turning

Cyril Griesbach

>Good job, Don. But I have to say...you need a bigger roughing gouge.

Re: BIG Turning *LINK*

#9

Re: BIG Turning

Don Orr

>Thanks, I really need a BIGGER LATHE !! I was surprised how well my 1 1/4" gouge did. I also tried a large bowl gouge but the RG worked the best.

Re: BIG Turning *LINK*

#10

Steven Antonucci

I can see metal in the log...

steve antonucci

>That black stain is your red flag. The local mill by me has tons of the stuff sitting on the side that they won't cut because of the metal staining.

Two hours at low RPM's would kill me. Ca Chunk. Ca Chunk...

Do you have a final finished picture? I don't know what you were trying to make?

Steve

Re: BIG Turning *LINK*

#11

Steven Antonucci

You must have been typing while I was...

steve antonucci

>Or I need to go find some coffee...

Steve

Re: BIG Turning *LINK*

#12

Re: BIG Turning

wilbur

>"Thanks, I really need a BIGGER LATHE !!"

Don't we all? :@)

I would guess that on this forum, that's sort of like saying, "I need oxygen!!"

Re: BIG Turning *LINK*

#13

JL

Just the long Jet bed extension :).

JL

>Though more power might be helpful. And how many times did you have to stop and sharpen your poor roughing gouge?

Re: BIG Turning *LINK*

#14

Re: Just the long Jet bed extension :).

Don Orr

>You're right about the power, it's only 1.5 HP. I was actually pleasantly surprised how well the machine handled this massive chunk of wood. I did have to sharpen several times. I had thought about the bed extension beforehand but when I measured I figured I did not need it and I was right, fortunately.

Re: BIG Turning *LINK*

#15

Re: I can see metal in the log...

Don Orr

>You are right Steve. I went through a nail with the chainsaw when I was trimming the ends. I was able to remove the remaining nail easily. It left a beautiful multicolored streak deep into the wood. I knew there was a good chance of metal since the sawyer ruined several blades on this particular tree. And yes there was a lot of ca-chunk, ca-chunk, ca-chunk. It really was fun though.