Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Preparing Platter Blanks

Posts

Preparing Platter Blanks

#1

Preparing Platter Blanks

DD

>I have three oak pieces that I would like to turn into platters. I need to rough turn them, but I realized I really don't know what has to be done to rough the platters out. Each of the blanks that I have are about 13" in diameter and 3-4" thick. They were cut about 3 months ago, so are still no where near dry. Is it simply a matter of turning them round and then to about 1-2" in diameter and then let them dry out?

Thanks.

Doug

Re: Preparing Platter Blanks

#2

Re: Preparing Platter Blanks

Norm Smith

>Doug, I would let them dry as is before I did anything to them. I am assuming that they are sealed.

Norm

Re: Preparing Platter Blanks

#3

Re: Preparing Platter Blanks

DD

>I have sealed the end grain on these. . With humidity levels decreasing with fall (Ottawa), they should dry, I guess, in another 3 months. I'll give it go then. Thanks.

Doug

Re: Preparing Platter Blanks

#4

Ric Taylor

Re: Preparing Platter Blanks

Ric Taylor

>DD,

The popular theory, which varies widely and is disputed by some, is that wood takes a year for every inch of thickness to dry. There are many factors that go into that and the results cover a broad spectrum.

Realize that many types of oak have a tendency to split and warp as they dry. Be sure that at least the end grain is sealed, I would seal the entire surface.

Ric

Re: Preparing Platter Blanks

#5

most oaks are difficult to dry...

GaryG in MD

>Doug,

Most oaks have a very high warp ratio. See

http://web.hypersurf.com/~charlie2/Turning/WoodShrinkage/ShrinkageT_R_TR_ratio.html White oak is in the middle, but the red/black oaks are at the bad end of the scale. That makes it likely that your blanks will crack as they dry, and it also means that if you turn round roughouts, they will become quite oval and no longer flat.

See http://books.google.com/books?id=hW13qhOFa7gC&pg=RA1-PA306&lpg=RA1-PA306&dq=wood+shrinkage+ratio&source=web&ots=OESI1nym5N&sig=0sym8JCwDcFrkVnsx-y-eGSDp-c&hl=en&sa=X&oi=book_result&resnum=4&ct=result

for specific comments on oak.

Other turners here may differ, but I think your best bet is to turn them round, or nearly so, keeping the maximum possible diameter, and to something like twice your desired final thickness. Immediately recoat them completely with a sealer. Keep them in a place like a wine cellar -- cool, dark, high humidity -- for at least a year.

Alternately, if you have the capability, you might consider boiling them right now. You can look up the procedure here and elsewhere. Many people find this to be quite helpful. See, for example, the experience of Jim King, for whom boiling is SOP. That may go a long way to reducing the probability of cracking, and it will shorten the drying time considerably.

When they're dry and you re-turn them to round, you can expect to lose around an inch of diameter. They will probably move again too, so if you want them really flat, leave them a little thick because you may have to re-turn them a second time after a day or two.

You will also find that turning dry oak isn't much different from turning stone. Expect a lot of dust even with a sharp gouge.

Good luck, and let us know how it turns out. ...Gary

Re: Preparing Platter Blanks

#6

BTW...

GaryG in MD

>Plan to get a good cut with your tools and don't expect to do much sanding, because the summer wood is very soft, and with sanding, you'll get waves or ripples. DAMHIK. ...Gary

Re: Preparing Platter Blanks

#7

Re: BTW...

DD

>The Oak I have is red, and was cut in March. It was likely felled quite a bit early than that, late fall perhaps. The two roughed out bowls I have created in Jun and Jul from the wood given to me indicated the wood was still quite wet. I'll bring my blanks down in size and seal them and see what happens.

Doug

Re: Preparing Platter Blanks

#8

A coincidence *LINK*

John K Jordan

>DD,

I talked to Frank Penta about platters last week (he is one amazing platter maker!) Frank said he always uses dry wood and prefers it 2" thick. If the wood is not kiln dry, he lets it air dry indoors before turning. I've seen some rough turned platters warp significantly. Oak can warp a great deal unless it is quartersawn straight down the trunk. If it is flatsawn it will cup; if flatsawn at an angle it will cup and twist.

4" seems a bit too thick. If you know someone with a bandsaw mill they might be able to resaw it into two pieces.

The document about platters on Frank's web site (link below) might be useful.

JKJ


Frank Penta on turning platters