Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Walnut getting on my last nerve-

Posts

Walnut getting on my last nerve-

#1

Walnut getting on my last nerve-

Ray Binnicker

>Is there anyone beside me that has problems sanding walnut? Long grain is ok, but the end grain is about to get the best of me ! I did manage to complete a small end grain box today, only after I broke out the power sanding pads and drill motor.

Ray Binnicker

Re: Walnut getting on my last nerve-

#2

Re: Walnut getting on my last nerve-

Dick Coers

>Ray,

You might try taking a slightly damp rag and wipe down the walnut after 220 grit or so. It will swell the grain and the scratches and when it is dry it will sand off the marks easier. I do the same with cherry and don't get as many scratches showing when my bifocals tell me I did a "good" job sanding.

Re: Walnut getting on my last nerve-

#3

Keith Tompkins

Re: Walnut getting on my last nerve-

keith tompkins

>HI Ray, the secret is a clean cut, with very sharp tools and proper presentation, walnut will cut so cleanly almost no sanding is needed. I cut end grain with the tool (detail gouge) on its side, flute facing away from the cut, right on the centerline. Don't force the cut, let the tool almost feed itself. Works even on the most highly figured walnut, or any wood for that matter.

Re: Walnut getting on my last nerve-

#4

Re: Walnut getting on my last nerve-

ken

>I don't know what speed you sand at,but I turn a LOT of walnut and if you sand to high RPM it will leave scratches.I have turned it so smooth that I start sanding with 180,but I if don't sand at a VERY slow speed it will leave scratches and I go thru the grits and then wet sand up to 1200 sometimes.Wish I could offer more help.

Ken

Re: Walnut getting on my last nerve-

#5

Re: Walnut getting on my last nerve-

Ron McKinley

>I think I'm missing something here. You say, "I cut end grain with the tool (detail gouge) on its side, flute facing away from the cut, right on the centerline." You must mean the flute FACING the cut? .....Ron

Re: Walnut getting on my last nerve-

#6

Re: Walnut getting on my last nerve-

Don at Central Illinois

>I'm a little confused too. Can you draw a small diagram explaining how this cut is made? I have a lot of walnut, I just haven't started on much of it yet, and anything that will reduce sanding is OK in my book.

Re: Walnut getting on my last nerve-

#7

Re: Walnut getting on my last nerve-

Ray Binnicker

>Thanks for the advice, guys. I went out this morning (retired, you know (gloat, gloat) and put your advice to practice. I completed another small box with considerably better results. Slowing the speed down, a little dampness, and patience (something I'm not strong on)seemed to make things go better.

Thanks again

Ray Binnicker

Re: Walnut getting on my last nerve-

#8

Re: Walnut getting on my last nerve-

john lucas

>Everything is relative. I finally got to meet Lissi Oland this week and she was pointing out a Walnut bowl that had an endgrain sanding problem she was dealing with. She has been turning longer than many of us have been alive so it happens to the best of us. I wish I had take a photo. This was a 28" walnut crotch bowl and was beautiful. Even then it was only priced at $450.

Re: Walnut getting on my last nerve-

#9

Keith Tompkins

Re: Walnut getting on my last nerve-

keith tompkins

>This should help, Keith


img

Re: Walnut getting on my last nerve-

#10

Re: Walnut getting on my last nerve-

Don at Central Illinois

>Thanks. That's what I needed.

Re: Walnut getting on my last nerve-

#11

ebd

Re: Walnut getting on my last nerve-

ebd

>Black walnut has the tendancy to bruise easily. Once you get sub-surface damage it's nearly impossible to sand out. As others have said, clean cuts are essential.

Re: Walnut getting on my last nerve-

#12

Re: Walnut getting on my last nerve-

John K Jordan

>She inspired me to try something bigger. (But nothing like the one she had on the lathe - that monster was 33" in diameter!) I brought home a set of her "big stuff" tools.

JKJ