Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

thin walled bowls

Posts

thin walled bowls

#1

thin walled bowls

BQ in VT

>After having a crappy day - 3 bowls went south on me, I am turning to you knowledgeable folks. I turn thin walled, 1/16" +/-, bowls. I have problems getting the walls a consistent thickness. I am also having the tendency thses days of turing the walls to thin, usually so that light passes through and the rim will be much thicker. There is the ever present danger of a catch when the bowls are that thin. I had that happen today also...Things usually turn go terribly wrong when trying to make that "last cut" to try to fix some of the aformentioned problems. I am in a rut (no fun) and any advice would be greatly appreciated. As always, thank you in advance.

Re: thin walled bowls

#2

Keith Tompkins

Re: thin walled bowls

keith tompkins

>Hi BQ, Catches and thin walls don't go too well together. Figure out how and why you are getting catches, and correct the problem; if necessary, seek advice from the best turner you can find who turns very thin. I assume you get the rim thin first, then work your way down, without going back to the rim once done.

Re: thin walled bowls

#3

Ric Taylor

Re: thin walled bowls

Ric Taylor

>BQ,

You didn't say whether your wood is green or dry. You will have more trouble with ultra-thin walls with green wood because it warps while you are working on it. When it isn't round, it is easier to get a catch.

With dry wood, this is less of a problem because it is more stable and less prone to warping.

When I'm trying to do something untra-thin, I find the 60-grit gouge is very helpful, and almost impossible to get a catch with .... :)

Ric

Re: thin walled bowls

#4

Re: thin walled bowls

Dick Coers

>You don't say what diameter you are turning, or what grind you have on the gouge. Difficulty goes way up with larger diameter. Start around 4" bowls to get your technique, along with a swept back grind. I pretty much make the last pass or two one handed , because I have my other hand on the outside of the bowl to dampen vibration. I have my fingers on the outside of the bowl and use my thumb as a fulcrum to start the cut. Do you try to cut the entire bowl thin in one pass? I work about an 1" or 1 1/2" at a time, making the final thinning cuts as I go. The rest of the bowl will have about 3/16" wall. Depends on size. After the first inch is thin you have to come back and work the next inch. When it gets close, you feel the bevel and start the cut on the first thin inch to blend in the final wall thickness.

Re: thin walled bowls

#5

Re: thin walled bowls

Bill Howatt

>I agree with Dick, you have to carefully complete the work as you go from the rim to the bottom in order to have sufficient support. Vibration and flexing is likely what is causing catches - it only takes a few extra thou of wood on the tool to cause it dig in.

You can try a bowl steady as another way to stabilize the side. If you have a variable speed lathe search for a reasonable turning speed that minimizes vibration.

Bill

Re: thin walled bowls

#6

Re: thin walled bowls

john lucas

>I do the same as the other 2 on thin bowls. I turn them thin an inch at a time and then don't go back. If you are having trouble blending the area of the first cut with the second, try taking extremely light cuts with your left hand on the outside to stabilize the bowl. You might also try shear scraping with the bowl gouge if your gouge has wings. If your not comfortable with that try shear cutting with a smaller round nose scraper.

Re: thin walled bowls

#7

Re: thin walled bowls

Dick Coers

>No kidding John, a scraper on thin walls? Has that worked for you? It's a sure way for me to blow one up. Nearly a 100 percent chance if I get up the wall much at all. Slightly off topic, but are you coming to Indyfest?

Re: thin walled bowls

#8

Re: thin walled bowls

john lucas

>Shear scraping Dick usually with my free hand on the outside. If I try flat scraping I blow them up. Most of the time if I'm going thin enough to be translucent I use the bowl gouge in shear scrape mode with my free hand on the outside. I learned this from the guy who turns lamp shades. I'm having a senior moment and can't remember his name right now.

Re: thin walled bowls

#9

Re: thin walled bowls

Greg Burnard

>John, Are you thinking of Andre Martel?