Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Dogwood and Black Locust Boxes

Posts

Dogwood and Black Locust Boxes

#1

Dogwood and Black Locust Boxes

Ray Binnicker

>OK,

My post on Sunday has been looked at by a good many folks, but no responses. This first one is of Dogwood and 4" tall and 3" wide. The other is of Black Locust and is 3" tall and 3 1/4" wide. The lids are not "pop" fit but are just free enough to lift off without holding the bottom of the box. The finish is 320 grit and EEE and beeswax.

Thanks for looking

Ray Binnicker


img

Re: Dogwood and Black Locust Boxes

#2

Re: Dogwood and Black Locust Boxes

Ray Binnicker

>This shows the lids off.

Ray


img

Re: Dogwood and Black Locust Boxes

#3

Re: Dogwood and Black Locust Boxes

Michael Stafford

>Sorry Ray, I had missed your posts. Shame on me as much as I love to see boxes. Your finish looks great but the shadows in your picture make it difficult to assess your form. I think you have done an admirable job for your first few boxes.

You might want to look in the articles section and use the information in Jamie Donaldson's Phrugal Photos Studio article. It will help you to get better pictures.

Re: Dogwood and Black Locust Boxes

#4

Re: Dogwood and Black Locust Boxes

Ed Moore in SW Virginia

>Ray,

It is clear that you are seeking a critique and some guidance. It helps to understand the person who offers comments, so let me begin by saying that I like crisp details. That doesn't mean that I am right, just that I have that bias.

So, looking at the box on the right I can say that I would have put a little crisp cap on the top instead of a rounded knob - like the top section on the left-hand box. Or, I would have taken the point off and made an ogee-like top that is lower. The edge of the locust top could be cut down like Mike Stafford does on his tops - and like the edge of the top of the dogwood box. I like the profile of the base of the locust box and how it flares out at the bottom.

The top of the dogwood box is interesting. I think that you would have a more interesting box if the base were more rounded or "fat". This might be accomplished by making the very bottom of the box about two-thirds of the current dimension and adjusting the curve to accommodate that. I am saying that you should consider having a 2" diameter footprint instead of 3" and that you should keep the overall diameter.

It looks as if you have sanded very carefully and finished the boxes very well. If these were your first boxes then you have done extremely well. My comments were intended to make you think about some design issues for future boxes. Good job.

Ed

Re: Dogwood and Black Locust Boxes

#5

Re: Dogwood and Black Locust Boxes

Ray Binnicker

>Thanks Mike,

I knew going in my photgraphy skills left a lot to be desired. I just finished reading the article you mentioned, and made a copy of it. It's good to hear positive remarks on the finish. One of my many "turning faults" has been I seem to get in a hurry toward the end of a project and want to see the finished piece "right now". I have been trying to slow down, take the little extra time to go back over a area that may need a little more attention.

Thanks again

Ray

Re: Dogwood and Black Locust Boxes

#6

Re: Dogwood and Black Locust Boxes

Ray Binnicker

>Thanks Ed,

Your comments are taken well; Thank you ! I've got the boxes sitting here in front of me and am applying your thoughts to them mentally. I, too, like the bottom on the Locust box better. I did when I turned it. I see exactly what you mean about the Dogwood box and making the footprint smaller and keeping the same thickness. OK, back to the lathe.

Thanks again

Ray