Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

router carving feet

Posts

router carving feet

#1

router carving feet

john lucas

>I'm building a Gavel for our club president. He needs it to keep us inline. I thought the striker block needed feet to create more sound. I decided to use my banjo mounted router table to carve the feet. I used the index wheel to mark off the feet. Then I put clamps on the index wheel to use as stops. I set the edged of the table up to control the depth of cut on 2 directions, forward and to the left. Then I just pushed the router in to take a shallow cut and rotated the index wheel. Push the router in further and make another one. Keep going until I have the full depth. It was really easy and clean enough to require only light sanding.


img

Re: router carving feet

#2

almost finished gavel and block 

john lucas

>


img

Re: router carving feet

#3

Re: almost finished gavel and block

bill Crommett

>John:: What did you use for texturing around the center of the striker pad ?

Re: router carving feet

#4

Keith Tompkins

Re: almost finished gavel and block

Keith Tompkins

>Great job, John. Clever, too.

Re: router carving feet

#5

Re: almost finished gavel and block

john lucas

>I used the Sorby texturing tool. I also textured the center of the underside. I textured the handle of the gavel using the Dremel engraver with a rounded over bit. I'll have better photos after I finish it later tonight. I'll probably shoot it sometime in the next few days. We are in the middle of sorting and sending out the graduation photos so my time will be pretty limited for the next 3 or 4 days.

Re: router carving feet

#6

Thanks Keith

john lucas

>

Re: router carving feet

#7

Steven Antonucci

Too pretty to hit...

steve antonucci

>Good work on both pieces. I like the creative engineering used to get the feet done.

Do you have a jig for holding the gavel heads to make them perfect on the surface or just a lot of sanding on the one side ofter parting off?

Steve

Re: router carving feet

#8

A lot of sanding after parting.

john lucas

>Actually not too much. I use the toe of the skew to finish the headstock end until there is only a small area left, about 3/8 to 1/4". Then I carve this off followed by sanding. It goes pretty quick.

My best friend does these only his finish is more utilitarian. I cuts close to the end and then cuts it off with the bandsaw. Then he hits it with a belt sander from 3 directions to flatten that end and then goes to hand sanding with 150 and then 220. He turns a gavel in half the time I do.

Re: router carving feet

#9

Re: Too pretty to hit...

John K Jordan

>I'll have to try the belt sander method!!!

I made mine with help from a jam chuck to finish the second end. But of course, I'm probably the slowest gavel maker East of the Mississippi.

(I love the idea of feet to raise the striker block a little.)

JKJ


img

Re: router carving feet

#10

Re: router carving feet

Bob Macgregor

>So, does it make a louder bang with the feet than without?

Re: router carving feet

#11

Re: router carving feet

john lucas

>bob I don't know if the sound is louder. It is different. This is the first one I've made and I think I made a few mistakes. I hollowed out the back, possible too much. If you hit it hard it could possibly break it. That brings me to the second problem. I didn't pay attention to the foot placement. I got lucky and the grain runs just slightly off a line from 2 of the feet. I think I should have put the feet exactly on the grain line to make it stronger.

If I was making this for a big gavel for daily use I would not put the feet on or would have made the block thicker to accomodate being hit forcefully.

This one is more of a presentation piece.