Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

router speed control for Foredom?

Posts

router speed control for Foredom?

#1

router speed control for Foredom?

Mark Wollschlager

>After trying to stand and use the Foredom foot pedal with limited success I decided to seek alternative speed controls.

The Foredom dial speed control looks nice, but is a special/internet order around here.

I saw a router speed control at HF that was cheap enough to try on a whim( $20).

I that a reasonable way to control the speed of the tool?

It seems like the motor type is compatible.

Anybody use one of those for their Foredom?

Thanks,

Mark.

Re: router speed control for Foredom?

#2

Re: router speed control for Foredom?

john lucas

>Mark I think it would work but haven't tried it yet. I found putting the foot pedal sideways makes it easier to use especially when you need the slower speeds. I spend part of today using mine to cut some slots and details in a piece.

Re: router speed control for Foredom?

#3

Re: router speed control for Foredom?

Ralph

>Mark, if you are certain it's the same type motor, it should work. But I suspect (without doing one bit of research) that it's not the same type.

Re: router speed control for Foredom?

#4

Re: router speed control for Foredom?

Clay Foster

>I've been using that setup for years, and it works fine. I like it better than the foot pedal.

Re: router speed control for Foredom?

#5

Re: router speed control for Foredom?

Ken Grunke from SW WI

>If the Foredom uses a universal motor with brushes, it should work as long as the control can handle the amps draw.

Re: router speed control for Foredom?

#6

Re: router speed control for Foredom?

Douglas

>A few years ago I got the harbor freight speed control you are interested in. It worked on the router but it reduce the torque so much that it was uslesss. I took it back and got my money back.

Not sure how it will work on the foredom but you can always try like I did and if it doesn't work take it back.

Re: router speed control for Foredom?

#7

Re: router speed control for Foredom?

bowlman

>I have used a router controller for years on my Foredom. Sure beats the foot pedal. Some of the carving catalogues now carry the speed controller as an option. Check out Treeline and Mountain Woodcarvers.

Re: router speed control for Foredom?

#8

woodcarverssupply.com *LINK*

Bob Elliott

>For $10 more you could get a good one. I have this one and opted to get it instead of the "gas pedal" type. It seems it will work on those shop built wood burners too.

Here's what it says on their site:

VARIABLE SPEED CONTROL, Add this to your 1/3hp MASTERCARVER� PRO-FLEX or other flexible shaft system or motor tool i.e. Dremel or Woodhogtm to vary the speed by dial control. This is a stand alone dial control. It varies speed up to maximum rpm of tool. Will also vary the heat of a wood burning pen up to the maximum power of your pen. Note: it accepts pens up to 400 watts, will not increase pen's power. Simple connection, power cord just plugs in. 797139


img

woodcarvers supply

Re: router speed control for Foredom?

#9

Re: router speed control for Foredom?

Jerry Bennett

>Mark,

You are right, about the �gas pedal� type controller. For a while I mounted mine on the table leg at knee height, probably like what John Lucas did. That works OK for short periods of time.

Now I use a Foredom tabletop controller with a dead-man foot switch. I did use a HF controller for a while but the speed vs. power variation was wide and it became a nuisance.

Re: router speed control for Foredom?

#10

Re: router speed control for Foredom?

Bruce Lane

>My understanding...for what it's worth.

By placing a variable resistor, such as a light dimmer, in line with an electric (AC) motor is merely attenuating the voltage. While this will in fact slow the motor, it is also very hard on a motor. It will also greatly reduce the power/torque of a motor.

After noodling around some, I was able to locate a circuit design that would allow you to build your own AC motor speed control. I remember building this some 30+ years ago in high school for the drill in the electronics lab. Worked very well.

If I failed at attaching the link you can manually enter the following: http://home.maine.rr.com/randylinscott/aug99.htm

I would imagine this could be put together at a very reasonable price with a visit to your local Radio Shack, Fryes, or electronics component store. You may even get lucky and find someone that understands what a SCR is and how it works. (don't count on it) :-)

Bruce

Re: router speed control for Foredom?

#11

Re: router speed control for Foredom?

Mark Wollschlager

>Thanks all for the info.

I decided to try it out and did find low torque at low speed.

Mostly I will be working at higher speeds where it seems to do OK.

I just got tired of surging/variable speed if I shifted my weight with the pedal.

I will look into the master carver variable speed control.

It is a pretty good price.

Mark.

Re: router speed control for Foredom?

#12

router speed control - from Woodcraft

John K Jordan

>Mark,

I bought a router speed control recently from Woodcraft for $30 something. It works well with my Foredom with no hint of loss of torque. I can't remember the brand.

JKJ