Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Sanding small hollow forms

Posts

Sanding small hollow forms

#1

Sanding small hollow forms

Galen Vetterick

>I am looking for suggestions on how you sand the interior of hollow forms. I have not found much on the internet when it comes to sanding hollow forms. I have done my first two small bowls about 6 1/2" dia. by 2 1/4" deep with 2 3/4" top opening. Until my turning becomes better I still have tear out and tool marks from Sorby multitip hollowing tool. Sorby advised how to reshape the cutter that helps. Working on that part! A 2" pad only gets the bottom. Used the finger method to hand sand the inner top and side while turning on the lathe and still have my fingers. Suggestions on how to sand these small form interiors? Thanks

Re: Sanding small hollow forms

#2

Re: Sanding small hollow forms

Carole Valentine

>I use locking 12" curved forceps with a bit of sandpaper folded around a piece of hard sponge or something similar (the foam blocks that come with micro-mesh are perfect) Just don't EVER EVER EVER put your fingers through the holes in the handles of the forceps while you are doing this! Should it catch you are in for a very painful and damaging experience.

Re: Sanding small hollow forms

#3

Re: Sanding small hollow forms

Galen Vetterick

>Thanks Carole

Sounds better than my ground off finger nails for sure!

If you have the web site and gallery of minutires under same name then it looks like advice from a very good source!! If your turnings are done on a Jet mini lathe, that is what I just started turning on, Jet 1224. At least maybe I started on a good little lathe. Looks like I have a LOOONG way to go to come close to the turnings I see in that gallery. Wonderful work, if your.

Re: Sanding small hollow forms

#4

Re: Sanding small hollow forms

keith zimmerman, Normal IL

>I have recently been wrapping a 3/8" dowel with sandpaper, leaving an overhang, and sticking it into the opening on my mini hollow forms. The overhang allows me to get the bottom and about 2/3s the way up the sides.

keithz

Re: Sanding small hollow forms

#5

Dick Hines

Re: Sanding small hollow forms

Dick Hines

>I saw a post some where about sanding the inside of hollow froms. The giuy used a bolt and cloth backed sandpaper. He cut the sand paper in into strips and drilled a hole through them and ran a nut on the paper. Said it worked great.

I will try to see if I can find the post.

Re: Sanding small hollow forms

#6

Re: Sanding small hollow forms

Bill Leathers

>Galen , I,ve turned a dowel with a bulbous end where you can glue a small square of velcro(bought at Lowes). From there you can adhere one of those round velcro sensitive sandpapers(cut to shape). It's either that or square the top of the hollow form , glue a piece of blackwood and turn a beautiful shape with a small opening that nare a pinky can explore the inner walls. Bill

Re: Sanding small hollow forms

#7

Re: Sanding small hollow forms

Tommy Holmes

>I turned a dowel (1" to 1-1/4)and dished the end inward and glued a small tennis ball (picked up at a pet supply store) to it, then glued velcro to that. Has worked pretty well so far.

Re: Sanding small hollow forms

#8

Re: Sanding small hollow forms

Galen Vetterick

>Thanks all for the suggestions! Got me to thinking why not use some of my old tooth brushes and heat bend end to different shapes and glue on velcor for pads. Kinda like a soft handled dowel. Got an old goose neck semi-rigid conduit desk lamp so maybe it would make a shapeable shaft to fit the small ball or shaped dowel end? Too bad my electric tooth brush has a short shaft or maybe it would make a mini rotary sander!!!!

Thanks again for all our suggestions.

A friend just left me some 12" diameter honey locust logs and would be my first green turning material. Not sure I have heard of turners using this wood. Maybe a poor choice, but it was free.

Re: Sanding small hollow forms

#9

Re: Sanding small hollow forms

Don at Central Illinois

>Honey locust is a great wood to turn. If I can find some photos tonight I'll try to remember to post them.

Re: Sanding small hollow forms

#10

Re: Sanding small hollow forms

Galen Vetterick

>I had time to try the tooth brush "tools" as no forceps or dowel handy to try other ideas. Used my heat gun to bend the ends with one for underside of rim and one for bottom and curved side. CA glued velcor to back of brush head and roled up onto head ends and sides and then cut pads about 3/4" by 1 1/2". The handles have enough flex they yield a little to too much pressure or with coarser grit. I probably got too radical with one at almost 90 degree head bend. I need to play some shapes and twists for any custom bowl shape. They held up well from 100 to 320 grit pads. Left brushes cut short on other side of head for stiffness to brush out dust as well. Used the longer sculptured plastic and rubber Oral-B type brushes but I can see even the cheaper plain brushes would let me adapt them into a home made wood handle to reach into deeper turnings. Don't know how to send pictures but maybe some will get the idea of what I did. Now I need new brushes for cleaning small parts again. Probably time to visit dentist and get free brush anyway!

Re: Sanding small hollow forms

#11

Re: Sanding small hollow forms

John Jordan

>Honey Locust is primo green turning wood. It's stable and retains it's color. Be careful not to heat check it when sanding. Regarding sanding the inside, it's not really needed if the opening is relatively small. In other words, the inside is not visually part of the piece. If it is simply a closed form, then it's a different consideration.

Note that I did NOT say it doesn't matter since you can't see it. You want to do a nice job with your tools, relatively smooth and relatively even. Sanding the inside will not improve the piece, and poorly sanded tool marks, or half sanded interior are even worse. Practice your finish cuts, being nice and smooth with your movements. A fresh, sharp edge (always),a nice smooth tool rest, and some paraffin, beeswax or such on the rest just before the finish cuts will help a lot.

Good luck.

John

Re: Sanding small hollow forms

#12

Re: Sanding small hollow forms

Ralph Watts

>Galen,

A couple of years ago I made myself some "sanding sticks". I have attached a couple of photos of the sticks. The pads are gripped with little spikes and can be rotated to get under shoulders. The ring moves down to open the jaws then slides up and snaps into place to hold everything together. They can be built any size--fit any hole you can turn in... If you would like to try these things, I'll send a pic of how to build. Best regards, Ralph


img

Re: Sanding small hollow forms

#13

Re: Sanding small hollow forms

Galen Vetterick

>Ralph

Thanks for sharing your picture. You give a whole new meaning to the word "sticks"! What an interesting design. I see the top knob must be turned to accept and capture the flared top end. Double face tapped to turn "sticks"? Like I am still fighting the skew and you want to throw in carved ends too! Oh and turned a thin ring! Maybe someday if I live that long! I'm just in the pens, to wine stoppers, to small bowls, and now trying hollow form and have not mastered any, but enjoying the time to learn the last six months.

Only my first attempt at a closed bowl if the picture comes through.


img

Re: Sanding small hollow forms

#14

Re: Sanding small hollow forms

John K Jordan

>>...You give a whole new meaning to the word "sticks"

Ralph doesn't do anything halfway!

JKJ

Re: Sanding small hollow forms

#15

Re: Sanding small hollow forms

Carole Valentine

>Thank, you Galen. I do most of my turning now on a Nova DVR but I still have my Jet Mini. It's a sweet little lathe. When you take your finishing cuts on the inside of the piece, take very, very light cuts and move the tool smoothly so you gradually cut the tops off any ridges until the interior is smooth. You don't want the tool to ride down in the valleys between the ridges...that will just amplify them.

Re: Sanding small hollow forms

#16

Re: Sanding small hollow forms

Galen Vetterick

>Carole:

Since my current hollowing tool is a Sorby RS200KT I was given the new shape for the cutter from Clive Brooks at Sorby. He thinks it will help me reduce cutting ridges with the trailing side of the cutter that is currently more of a point. Maybe this is known by the more experienced turners.

The Nova DVR lathe is an interesting design with the direct drive and wide range variable speed. I watched video where turners also say the reverse mode is a nice feature in some turnings and sanding.

I know I need to work on tool movement for hollowing and is not like turning an open bowl where I can see the bevel rubbing and make a bowl gouge cut right.

Also need to realize at what times I need to turn the speed up or down to help with my cutting. Think at times I run too often on two lower speed pulley on the Jet 1224 and maybe should turn at higher speed.

Current wood is limited to purchased 10/4 cherry but now have some green honey locust logs to try.

I see you have turned a large variety of woods and wish I had experience and then that kind of wood supply. I have not tried to turn end grain so that is for another time.

Glad I found this web site and people who are interested in helping.

Thanks


img