Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Skew's me

Posts

Skew's me

#1

Skew's me

jim canning

>All right I have been turning for about 7 years now and I have this thing called a skew. Never used it, it just looked to funny to use!!! Well I thought that I knew how to use it, wrong. I just tried it on an almost finished bowl, well now it is finished. Now I have a big splinter and a bowl with a big splinter missing from it. The only thing that it is good for now is the fireplace this winter but I don't even have one.HELP!!!

My Question is.....are there any on line FREE video's that would show me the right way to use this *#@* skew?

Re: Skew's me

#2

Re: Skew's me

john lucas

>Jim I don't remember seeing a "free" skew video yet. Wish I knew how to put something on youtube I would do one tonight. Your first mistake was using the skew on a bowl. That's a very advanced technique. You gotta crawl before you walk.

Start with a scrap limb and work on just cutting flat areas while rubbing the bevel. You must keep the cutting line on the lower 1/3 of the blade. Most american turners use the "heel" or short edge down cutting technique while some european turners use the "toe" or long point down. They both work but you still have keep the cut on the lower 1/3.

Alan Lacer has an excellent video on how to use the skew and has an article in the september 2008 American Woodworker on using the skew. That might answer some of your questions. I just got it in the mail yesterday so you should be able to find it on store shelves.

Re: Skew's me

#3

Re: Skew's me *LINK*

Gordon Seto

>Nick Cook has a mini skew lesson on YouTube. It is very good.

Instead of getting a partial lesson and still frustrated, I suggest the DVD by Alan Lacer or Alan Batty. None of these two is free, but IMO worth every penny. If you can start sanding at the next finer grit, think about the time and sand paper you would save.


Nick Cook on YouTube

Re: Skew's me

#4

Re: Skew's me

Paul Zerjay

>After renting Alan Lacer's video I decided to use the skew as my only tool until I felt comfortable with it. After a couple weeks of using no other tool but the skew I started gaining confidence. Now I use it more frequently than any other tool, on spindles that is. I even thought to myself the other day how I should have started using this tool a long time ago. Oh BTW, Point down for me.

Re: Skew's me

#5

Re: Skew's me

Greg Haugen

>Jim,

I've been turning for three years and for the first 6 months all I had was a scraper and a skew. The skew is now my favorite tool by far. I agree with John, Bowls and skews are very advanced techniques and shouldn't be attempted.

First, what skew are you using? Standard, oval, or round?

Second, how are you sharpening it? No matter the method skews need to be sharp. Straight off of most grinder's won't be enough. Diamond hone or waterstone/oilstone at the minimum but could also power strop polish it.

What kind of Angle do you have on it. There are two different grinds, the standard or straight and the Radiused/Raffan/Lacer grind. A starting point, some choose to vary it, for either grind is 70 degrees between the toe and heel of the skew-point to point. The degree angle is the same one just has a flat section in the upper third then a radius down through the lower third (toe to heel).

Skews have two negative reactions, the skate and the catch. The skate occurs when the bevel is lifted off of wood and the edge cuts deep and "skates" backwards leaving a spiral in the wood. The catch occurs when the cutting action passes into the top half/third of the skew. It should be in the lower half/third. When the wood cuts higher on the skew the force changes from controlled to uncontrolled and the point is pulled into the wood where it usually "snap" "crackle" "pop" (rice crispies-just kidding- had to) will tear a section of wood out along with some of your nerves. Both reactions can be lessened by using a "safe driver", either the oneway cup driver, a steb driver, etc. In the case of a catch or skate the driver simply slips stopping the wood from spinning. A spur drive cannot slip and causes horrible catches. The "pressure" from the tailstock can also be adjusted to make the safe drive more or less sensitive.

Also, for learning the skew, I'd recommend ripping a 2x4 in half. It's pine, soft and inexpensive. Start with a 12" piece of the 1 1/2" square 2x4 with planing cuts to a cylinder, using "v" cuts, lay out some beads and roll them. When that's done. Plane off the beads and do it again, then again. The soft wood is great for learning the mechanics of the skew.

If you're in the WI, MN, or IA area, email me and I'd be happy to help you out. John Lucas is an excellent "tool technician" and he's in TN.

Alan Lacer and Nick Cook both have great sites with articles available on sharpening and using the skew.

Any questions just ask.

Hope that helps,

Greg H.

Re: Skew's me

#6

Re: Skew's me

Jennifer@Indy.USA

>Jim, I would suggest keeping the skew to between center work only. It�s really not designed for face plate work. The tang that holds the skew into the handle is much more apt to bend or snap off due to a catch on a bowl than a piece held between centers. The same goes for a roughing gouge. I'm assuming since you said the bowl is firewood now that you got a nasty catch with it, which means I would guess that you were using the skew in some other orientation than scraping the outside? For safety sake, I'd keep it away from your bowl work.

Just my measly 2 cents and worth every penny :)

Jennifer

Re: Skew's me

#7

Re: Skew's me

Greg Haugen

>I agree with Jennifer. There's only one person I know of that does it with any success and that's Terry Scott. The skew is a spindle tool.

Greg.

Re: Skew's me

#8

jim miles

Re: Skew's me

Jim Miles

>Some people get good with skews - for the rest of us this is the advice I heard somewhere and like the most: Hold the tool loosely with the point down, the handle raised, place it gently under the paint can lid, pry down and it will pop right off!

Re: Skew's me

#9

Steven Antonucci

Some practical advice for skew proficiency

steve antonucci

>I agree with most of the folks who have said to use the skew on spindle work, but I sometime use mine for a "final surface" with bowls or hollowforms in figured or punky wood. Best tool out there for clean cuts if you know how to use it.

1.) Get the spindle use down pat first. If you can't cut with the heel on a spindle, ain't going to get any better on a bowl.

2.) Make sure you are sharp. If you can't shave with it, it's not sharp.

3.) Slow the lathe down to minimize any catches. I'll often use the skew to get rid of a tenon on a bowl. That's a good place to start learning skew control with a bowl orientation. Slow speed makes it manageable.

4.) Take a super light cut. I wouldn't want long ribbons, just thin wispy shavings. If they aren't sticking to you from static electricity, it's probably to heavy of a cut.

5.) Practice on some practice bowls. If you have a bad one, use it to practice your tool work. Wear a shield (of course), and at the end of the session, break the bowl to resist "saving it"...

It can be done, and once you "master the skew", it will come.

Steven

Re: Skew's me

#10

Excellent response Greg

john lucas

>

Re: Skew's me

#11

another approach...

GaryG in MD

>I had the pleasure of attending two demos by Stu Batty this week.

Talk about information density! I learned more about turning and sharpening in ten minutes than in ten prior demos. But I digress...

Remember -- he came up as a spindle turner, starting at around age 11.

He was a professional spindle turner (where the word 'professional' meant more than that he sold stuff) at age 16.

He says now that he wasted a year of his life using a skew.

He demonstrated this by making a deep v-shaped cove in 11 skew cuts -- and then doing the same thing with a gouge in 4 cuts.

He will not touch a skew any more except to show off using it on bowls where it's not supposed to be used.

For all those amazing pieces he makes, he uses a bowl gouge, a spindle gouge, a negative rake scraper, and a beading/parting tool. And they're all ground to exactly the same 40-degree angle. It doesn't get much simpler than that. Actually, he says the skew makes a good negative-rake scraper. ;-)

With all due respect to those of you who are good with skews and like them, I'm with Stu and Jim -- use 'em to open paint cans. ...Gary

Re: Skew's me

#12

Re: another approach...

pat28

>Of course, every turner out there has his or her own preferences. As someone mentioned above, even before I started turning, I had heard the rumors about the horrible skew, and I guess this was enough to prompt me to get a solid hold of it. I got Alan Lacer's two skew videos (though the first one focuses on the techniques while the second is a project DVD) and I was amazed at the details and years of experience that Lacer presented there. He literally spends over 30 minutes dealing with tool shape, sharpening and honing. This takes care of the main problems people did not even know they had with their unmanageable skew.

As Greg pointed out above, Lacer stresses the fact that any skew (or lathe at that) should be purchased along with a dead center, or cup center, as the 4-prong or spur centers that almost all lathes are equipped with have no give. Any catch with those is bound to be carried to the extreme as the wood won't stop. With a cup center, any catch has a limited effect because the piece of wood simply slips when one occurs. The turner can even control the amount of "slippage" by simply reducing the pressure on the tailstock. Hence, as one is learning a new technique with the tool (and this could go for any other tool too), one can reduce the tension on the piece of wood and immediately increase one's confidence.

I now own two skews, a 1/2" and a 1". I definitely use the larger one more often as its weight reduces any chatter and offers great control. The smaller one is great for detail work or miniatures. For its versatility and the clean fnish it offers, I would never ever think of turning wood without one. Thanks to Alan Lacer!

Pat

Re: Skew's me

#13

Rob Wallace

Re: Skew's me

Rob Wallace

>In addition to Alan Lacer's two skew videos (BTW - get the "Dark side - Sweet side" video first - this one has more on technique than on skew projects found in the second video), be aware that Mike Darlow also has a video on use of the skew ("Taming of the Skew") in which he introduces some different aspects of skew use in a different manner than Alan does.....

I have taken Alan Lacer's hands-on class on use of the skew, and recommend it highly. Just as with all turning skill development, he recommends getting lots of practice....even if you aren't actually making anything except shavings....

..... as it has been said, every skew has a certain number of "built-in catches" that have to be used-up before it behaves properly. Practice tends to use-up those catches so you can get down to doing your skew work confidently and comfortably without errors when it really counts....

ALSO - Skews and bowl turning don't mix - reserve the skew for between centers work.....you can get equally smooth surfaces on bowls without using a skew with properly sharpened gouges and their proper use, including shear scraping.

Turn safely!

Rob Wallace

Re: Skew's me

#14

Re: another approach...

john lucas

>I love Stewart Batty. He's one of the sharpest turners I know. Not having seen what he was doing it's hard for me to understand how it takes 11 cuts to make a V cut. I do most V's even deep ones with 4 to 6 cuts.

I like his 40 degree gouge. I've been using it more and more although I tend to use it for final cuts. I can remove wood much faster with a gouge that has wings and 40 degree is too shallow for some of the bowl shapes I do so I go back to the 60 degree grind for these.

I still don't see the need for the cup center when spindle turning. Maybe I turn to aggressively but I stall the wood too easily when using a cup center. If you get a catch you still have a dig in that must be removed with more cuts so I don't see stopping the wood as an advantage. If you are learning the skew I can see it because the actual catch won't be as traumatic but you still have to correct the same error.

Re: Skew's me

#15

Re: another approach...

Greg Haugen

>One technique I learned from Alan Lacer when I was at his house, it's also on his first DVD, is to take a dremel tool with the "flame shaped" grinding stone and cut three grooves around the edge of the cup center. When that center is driven into the wood it creates "key," if you will, to drive the wood. In the event of a catch the cup center will still slip. By lining up the "key" you'll get alot of drive. By rotating it slightly it will have a little bit of slip. I've used it to drive 4 by 4 lamp columns and it drove it fine. A cup center without the "cuts" in the edge does slip a little too much, but still can be adjusted by pressure from the tailstock.

The steb drive from Sorby is another "safe" drive, but in my opinion-which doesn't matter much-has too many teeth and tends to slip too much. To drive a 4 by 4 you'd have to get a larger diameter driver, which they do make. Buying the 1/2" size will set you back $60 for the Sobry compared to $40 for the oneway cup center that works better with a simple modification.

I think of learning the skew like practicing the piano. You have to practice the chords and notes before you can put them together for a song.

Greg